20 Most Recent
HP LaserJet 3050 All-In-One Printer - Page 5 Questions & Answers
Error 0X00000015. HP laserjet 3050 won't scan
-
Without turning off the product, disconnect the USB cable from the rear of the product.
NOTE:
The USB cable connects to the port on the back of the product. The port is labeled with the USB icon (
).
Figure 2: Example USB connection (your product might not look exactly the same as this example)
-
Remove the cartridges from the product.
-
Wait for the 'Insert Cartridges
' message to display on the control panel.
-
Disconnect the power cord from the back of the product.
-
Wait 60 seconds.
-
Reconnect the power cord. If the product does not automatically turn on, press the Power button (
).
-
Reinsert the cartridges, and then close any open doors on the product.
-
If you receive a prompt to print a calibration page, do so.
-
Reconnect the USB cable to the rear of the product, and then try printing again.
Solution two: Service the product
If you have completed all the steps listed above and are still experiencing a problem, service the product.
If you need more help come back.Post /
thumbs / testimonial are
welcome!
Tricolor cartridge problem error message on HP 3050 J610
These
types of severe cartridge errors (i.e. Incompatible cartridges, Black/Color
cartridge(s) problem / Cartridge not intended for this printer, etc.) typically
indicate the internal micro-electronics of the HP 61 cartridge are electrically
damaged. The cartridges electrical wire runs at rear and lower side of the ink
cartridge are very delicate and are somewhat susceptible to ink attack over
time, which can lead to premature failures. In addition, the older the
cartridge the higher the chance of an internal electrical failure due to
prolonged ink exposure and subsequent circuit corrosion. I suggest you run a Tap 41 diagnostic test to
check cartridges electrical health (this is a forced service test so the
printer will attempt to send whether cartridges are good or not); Refer to
Inkjet411 youtube videos below:
HP 60, 60XL, 61, 61XL Ink Cartridge Refills - Solving
Errors & Warnings:http://www.youtube.com/watch?v=BskAfa6NJSg
HP Deskjet 1000-3056 Printer Models -- HP 61 Ink
Cartridges Tap 41 Diagnostics Testhttp://www.youtube.com/watch?v=tMZkqE36ifk
Feeder jam hp 3050 laser Print
Fisrt check if there damage or strange in the path of paper or , remove paper then with Wet clean pack up roller ,if you alcohol spary ,use it to clean rubber , hope help you Mohamed HejaziAfaqnama -
[email protected]
How to reset Language
When a super NVRAM init is performed, the all-in-one language and telecom country/region settings
are undefined. The user is prompted to set the language and telecom country/region. Until these settings
are defined, the all-in-one will not return to the Ready state.
CAUTION A Super NVRAM init erases all data that is stored in both the unprotected and
protected NVRAM memory.
To perform a super NVRAM init
1. Turn off the all-in-one.
2. Press and hold down the * and 5 buttons.
3. Continue to hold down the buttons while you turn on the all-in-one. Hold the buttons throughout
the entire power-on sequence.
4. When Permanent Storage Init. appears on the control-panel display, release the buttons.
5. When prompted, set the language and telecom country/region.
6. Allow the all-in-one to return to Ready before using it.
Scanner error 6
in my network i have hp M1005 printer always i'm getting this msg "scanner error 6 turn off
then turn on"
when i make turn off and turn on again same msg comming
how can i solve this problem...
Not finding what you are looking for?