20 Most Recent Casio EXILIM ZOOM EX-Z600 Digital Camera - Page 2 Questions & Answers

I would recomend you to reset the camera, this will not affect any of your saved pictures. This can be done simpely by acessing : Menu, settings, reset to facory settings (Factory settings)

I dont understand the question... you want to change "language options"?



Are you try with the User Guide EXZ600_e

Keep us updated.

I don't believe thats an actually issue. It's just warning you that there is insufficient light for a proper exposure. Try lighting the area or change the ISO setting to a higher setting (though this may cause film granularity - i.e. not the greatest looking picture). Hope this was helpful.

Hi. If you are using it in 'manual' mode there may not be anything wrong. If so, see if you can switch the mode dial to 'automatic' so the camera can adjust itself. If you need a User Guide it can be downloaded free here:- http://www.retrevo.com/support/Casio-EX-S600-Digital-Cameras-manual/id/200dj180/t/2/
Regards

Sorry to say its a Camera CCD problem. Mos expensive part of the camera. Visit a camera repair shop and ask the charge please. Near about 110$.

When you insert the card into the computer, look in "my computer"...it should show up as a "removable drive".

Your camera most likely has a lens error, this is such a common fault that I hope you don't mind me pasting my stock generic answer below. No point in reinventing the wheel!

Stuck lenses are probably the most common reason that compact digital cameras get thrown away, but there's a fair chance of recovering use of your camera again

The fault is commonly caused by dirt or grit blocking the mechanism, or due to it having suffered a recent fall. Another common cause is that the camera was in a pocket or bag and the power button accidentally activated and tried to open the lens against resistance. The mechanism may have simply become dislodged or there may be parts which have broken.

If your camera is still under warranty and has definitely not been subject to misuse then contact the Casio service department in your country to find out about a free repair. If the warranty has expired though a professional repair will far exceed the cost of replacing your camera. You will therefore have nothing to lose by trying to fix this yourself.

Please click here and you will be taken to an excellent article provided by the Camera Repair website. For the most part, you'll be guided on how to physically manipulate your camera to try and clear the fault. Although the article mentions Canon a few times, the advice applies equally to all cameras with lens errors and is not model-specific.

If the link doesn't work then cut and paste the following address into your browser:-

http://camerarepair.blogspot.com/2007/12/fixing-lens-error-on-digital-camera.html

Good luck, I hope you manage to use this information to fix your camera. Please take a moment to rate the free answer I have provided for you and any testimonial which you might wish to add is always welcome!

Hello

The problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the probability is that you will have to get it fixed by a professional.

Use these at own risk as it may further damage the camera.

Firstly , try connecting your ac adapter or usb cable.

Try holding the shutter button while switching on the camera.

Look at the lens , and if some of the lens 'circles' is misaligned or not concentric then try wiggling it (while holding camera lens down).

Try gently pushing or pulling the lens when it extends but this is risky as it may cause the lens barrel to slip out of its guidance system.

Another way to do this is to place the camera lens down on a hard surface and then power it up. Be sure to use a soft cloth or something similar as to not scratch your lens or casing. Let the lens push the camera up and down a few times and sometimes the little resistance provided by the camera is enough to get things going again.

Try hitting your camera near the lens on the body with the soft tissue on the palm of your hand.

Other than that , I would take the camera to a repair center for a evaluation to see if it would cost more to repair than to replace the camera.

If it is still under warranty I would suggest you take it in before trying any of these steps and remove any off-brand batteries or accessories as some stores are really fussy about warranty repairs on camera's with non-brand accessories.

You can also have a look at THIS link.

Hope the advise is useful. please do not hesitate to let me know if you need any further assistance.

Regards
Andrea

I have a casio exilim 8.1mp ex-z80 green digital camera. The casing is no longer presentable. Do you know where is the CASIO SERVICE CENTER here in the philippines, specially in davao city...

SD and SDHC cards have a slide switch along one edge. The position farthest from the contacts locks the card, protecting it from writes. The position nearest the contacts unlocks the card. If the switch is already in the proper position, slide it fully the other way and then back again.

Hi,
This kind of symptom comes when electronic aperture in lens mechanism does not work properly and fails to control light amount for good picture.
Lens assembly will be replaced to fix this issue and local camera repair shop will do the job.
Hope this info will help you.
Thanks.

My Nikon was having the same problem with the stationary black spot. I used a can of Dust Off ( the original compressed gas duster). I just removed the lens and held the camera upside down (lens facing the floor) and blew my compressed air inside and my black spot disappeared. Just a thought you might like to know !! Good luck.

No longer need your help have bought a new camera

Is it a new 4GB memory card? If so that might be your problem. The card would likely be an SDHC card, and your camera was designed before the SDHC format came out. Your camera can only use standard SD cards (2GB or less).

But if the card is less than 2GB, it could have become corrupted. In this case you could try formatting the card in the camera to see if this would rejuvenate it. This will also erase the card. See this post if you wish to first recover any pictures that may be on the card.

Finally, if this is occurring with multiple cards, and is also saying "card locked" even though the tiny slide switch is in the unlocked position, then see this post for a possible remedy.

Hi,

This sounds like a cracked screen.. a leaf you say? is the leaf a graphic, perhaps an icon..

Try transferring the pictures ot the system and see whether it works perfect, If it works perfect but if you see a black leaf on the screen , then you should change the LCD display

I would advice to take it to a certified repair center and replace the LCD panel.
Please leave me comment, if you need further assistance
Rnj VINODKUMAR

check and see if the little switch on the sd card is locked if so unlock it by switching up

Couple of things you can try.

First use a soft dry cloth and clean the lens. Those camera's have very small lens so it is very hard to tell if they are dirty or not. Don't use any kind of spray on the lens. If that doesn't work you might be pushing the shutter release button ( the button you use to take the picture) to soon. Some cameras need a second or two to focus and then you can take your shot. Try these tow things. If they don't work check your user guide to see if they have a problem solving area. If not go to the web page for your brand of camera and see if they have a customer support number or link.

Hope this helps.

the lens assembly needs cleaned or replaced that will have to be decided by a camera shop.