Top 20
Maytag Atlantis MAV6000 Top Load Washer Questions & Answers
My Maytag Atlantis (MAV7600AWW) just
it sounds like there is something stuck in the water pump you will need to lay the water outlet on the floor into a shallow vessal to empty it then that the back off locate the water pump and see if you can rotate the cooling propeller if not take the motor housing apart to remove the debris that's preventing it from turning if the motor has not burnt out eric
I have a maytag top
Press 2 metal tabs. About 6" from the sides on the front of washer. Plastic ring on top has tabs that need to be disengaged to disconnect the ring. Once ring has been removed the area between the plastic tub & metal tub is accessible. Check for small articles of clothing, like socks or underwear. Inner tub can be removed by: snap up plastic cap (small slot for tool to slip in and pop up). Remove 7/16 nut and remove agitator (may require to be rocked back & forth, sits on a splined shaft). Remove 5 small phillips screws, being careful not to drop any, and pull inner metal tub up (may require it being shimmied back and forth). Removing this tub will give full access to any debris or articles of clothing that may be under it. Please keep in mind that if you're challenged in reassembly
Remove maytag inner tub
Remove top cover, take out the bolt remove the small cover to expose the plate with several screws,remove the screws and lift the inner tub up. Usually this requires two people to get the tub up and out as it is very hard to pull up as it kind of sticks to the shaft
Will not spin
No spin, or lite spin try these:
Using a multi meter check for continuity the door switch, which when bad may not allow agitation or spin. The lid switch assembly can fail either mechanically or electrically.
Check the clutch, brake assembly and transmission, one way to check for slipping is to get under the machine after a spin cycle ( this is if u get a lil spin but not much leaving clothes still wet) mix in a spray bottle a lil water and some dish detergent, then spray it on the clutch assembly ( the metal round pc. Connected to the tranny) if it sizzles and steams up then u know its bad and slipping. Another way to check clutch if u get no spin at all? Is to take it out and use ur hand to try and turn the inner spring assembly pushing it around the inside? If its very easy, it BAD should be hard to push by hand.
Next check the motor coupler which engages the tub and tranny to the motor. ( if its bad u usually get no wash or spin or very little of either)
Next check for a loose, worn or broken belt if belt driven.
On some front load models u may need to check the STATOR assembly.
The stator is essentially one half of a motor, it interacts with the tub by creating a strong electro-magnet. If the stator burns out the washer won't spin or agitate. Check the stator for continuity. This part is often misdiagnosed.
Sometimes a no spin machine can be due to a plugged waterpump hose or obstructed water pump propeller. Check these by eye and hand.
HOW TO CLEAN INLINE SCREENS
Good question! I wondered this too... But I just did this last week and I was successful... Lets see if you can be too.
First.. How old are your hoses? Are they getting stiff? Maybe time to invest in new ones... Especially the hot one... For heat makes these hoses age quicker.. And pick up a couple screen type hose washers for each end, if they are not already on your new hoses... Or if you are not changing hoses this time.
OK... Now you see how to turn off the water?
Turn it off and bleed the pressure off by attempting to fill the machine....
Now a pair of slip joint pliers helps to loosen the connector. . start at the supply valve end... See the screen... Right there in the end of the hose? Is it dirty, clogged? Or maybe even rusted and failed? Maybe you are glad you invested in the new hose? If so, just install the new hose. If not... Do you have access to compressed air? Can you take the hose to a friend and blow it out?. If not try removing the screen type hose washer... If you have to destroy it getting it out... You have new washers.. Install them... Likely there is one at each end.
Now... Before you hook it all back up... Can you blow air thru the hose easily? Then hook up the hoses to the water supply ends at the wall... Put the hoses in an empty bucket... Turn on the water valve... Do you get a real strong flow of water? If so.. You are ready to connect to the washing machine end also. Now does the machine fill up g fast again? What did you find? Let us know... We are here to help. MB
Manage my life com sears
Draining problem;
About the noise. If stumbles on the wash cycle and no noise occurs, is transmission problem. If the noise is present all the time the coupler that is located between the transmission and motor needs to be replace!
Should water back up into the tub upon spin completion on maytag atlantis
No, If water is coming back, the sewer is cloged up or is a big posibility that the washers transmission is not spenning at all. it may sound like is agitating during the wash and spinning during the rinse. To check it, put soap inside the drum if it doesn't get disolved after the cycle is done. The transmission needs to be replace. Is costly you may want to shop for a new one.
Not finding what you are looking for?