20 Most Recent Maytag Neptune MLG2000A Front Load Stacked Washer/Dryer - Page 3 Questions & Answers

Hi christian742,


I highly recommend for you to read the Manual which came with the machine.
it should include detailed instructions on how to stop at the end cycle without pushing.

Is it beeping?

Have you checked to see if your belt is loose or worn?

this is a problem with the drive belt tension.needs to be adjusted.sometimes the problem might be solved by balancing the machine on ground.

Hi,

Here is a tip that I wrote about dryers and noises...

It will help you determine what is happening there...

Dryer Repair Squeaks, Grinding, Clicking and Knocking Noise


heatman101

Asker's Testimonial "That answer was very informative - thank you for taking the time to educate me. " - teresa241964

On this model there could be several reasons why the washer will not go into the spin cycle. The most common problem is the machine control board not providing voltage to the door lock wax motor. This type of diagnosing will require accessing the console area & inspecting the machine control board resistors. I am sending you an image showing where on the control board to look. If the R11 resistor is burnt like I suspect then you will need to replace the door lock wax motor & machine control board. If this diagnosis does not help I am sending you a list of other possibilities. On this model you may consider calling a service tech out to diagnose & repair. Also if you need help with parts please send in the serial number. Please see the images provided in the attachment below for further instructions.

definitly not worth fixing time for a new one.

You need the "motor conversion" for your machine. There is a new board and motor that need to be installed. Here is some info on it.

Sounds like there may be something obstructing the flow of water either inside the pump or from the pump to the drain hose. It requires disassembly. To access the pump, remove the 4 door screws that secure it to the frame and remove the frame, of course, remove plug first. The pump is located in the right mid rear section and has hoses and a water level switche attached to it. if you have a big towel, place it around the pump to capture the water and remove the clamps securing the hoses to see if there is anything in there. If not remove the drain hose and run a snake through it to see if there is an obstruction there. If not, you may need a new pump,.

Unplug the dryer and the first thing to do is check for the presence of 220 volts at the wall outlet. If you lost one leg of the 220 volts, it is possible for your dryer to run but there will not be any heat. Once you verified there is definitely 220 volts at the wall outlet, remove the rear cover. On the lower right hand side you will see a silver canister which contains the heating element. Remove the lower two wires directly from the heating element and check this for continuity. If it is good, on the left hand side of the same canister they often install a thermal safety which may have tripped. Do the same test as with the heating element. Remove the wires and test the thermal safety for continuity. If this is good, move to the blower housing on the left side of the exhaust vent and look for a white piece of plastic which has two wires on it. Remove these two wires and check this item for continuity.

you can follow this link below to find out how to test for individual components to find out what part is faulty...

http://www.partselect.com/dryer+dryer-wont-heat+repair.htm

You can also order for any replacement part from the following Websites

www.PartSelect.com

www.SearspartsDirect.com

If you found my solution of any help ... please do not forget to rate the solution

my neptune was so loud it sounded like it was taking off, it turned out to be the bearing in the drum, the repair man wanted $1200. to fix it. i called maytag and this part has a lifetime warranty and they sent it to me in 2 days.

Check out this tip I wrote about the noise and vibration thatfront load washers can make..

Washer Problems Washer noise when spinning
heatman101

You need to clean the stationary "brush" that collects lint and debris from the water during the cycle. The brush can be seen around the tub directly touching it along the bottom/front of the device. Right were I pour my detergent in, after the cloths are in there. To remove the debris I use a bottle brush. You can expect to use trial and error for your attempts. As far as the water being left.... My device has always left water in the bowl. I periodically just run a cycle with no cloths and bleach...HOT.....Mine is not spinning at the moment...again....I think its another call to the local dealer....AGAIN....

The second rinse is when the softener cup is being flushed. Remove the dispenser and clean and inspect the housing to be sure no softener is gumming up the holes and blocking the water flow into the machine.

Hi,

Since there are couple of issues with the maytag washer, I am attaching an article which would guide you step by step how to troubleshoot each one of them.

http://www.maytag.com/content.jsp?name=troubleshoot_washers_neptune

Thanks

Thanks for contacting Fixya and please accept the solution if it has helped you.

Check for bent or loose pulleys. Check that belt is not stretched out, Some of these have a belt tensioner. Not sure if yours does or not. If it happens to have one, tighten it and see if that helps.

Hi,
A tiny screw driver and you can wiggle it in on the very edge of the screen and pop them out....
The other way is to reverse the hose and blow water backwards through them to clean the crud out...

heatman101