20 Most Recent Canon - SUPER G3 FAX BOARD-T1 (0450B002AA) - Page 7 Questions & Answers

I had same problem. I put in a big bunch of paper and then took out about half of it and it suddenly worked. Also try opening the lid and then closing.

Hi,
Please change the Leithium battery fixed inside your fax machine, usually this the problem.
If the Date time is running in different date & time.

Please press Menu, then scrolle left of right arrow key. When you find set Date/Time enter the key mentioned in the Display key and change to your date & time.

After some time see if the date/time working normally. If not change the above mentioned battery.

regards.

I have a cannon MF4100 that no longer scans. The print, copy, and fax, wrok fine but when I go to scan absolutely nothing happens. The scan did work but the other day just stopped working. I have not added any new HW or SW. Any suggestions? Thank You, KPG

need to know what kind of fax this is

My co-worker knew how to do it and she took care of it for me. I can't give details because she took care of it for the office.

I gave up on it. I was able to disassemble it and get to the power supply PCB but the main fuse was not blown. A new power supply PCB was too expensive and I don't have time to troubleshoot the power supply. Thanks
dewberr

Hi,

If you are using a multifunction printer, fax & copier it needs to be installed all color cartridges, black cartridge is not important

I`m trying to scan a multi paged document into my dell inspiron 1521 laptop , however when I scan the doc it will only scan into images not into microsoft word where I want to make changes before e-mailing the doc.-----I lost the original in microsoft when the old comp.crashed. Any suggestions would be appreciated.

ok..you troubleshoot your printer.Go to printers.click start,click printers and faxes.after you open the program, right-click on your printer icon then click properties then click print test page..this will test if your'e printer is functioning properly.. just make sure that there's a paper feed on the printer bay.ok?

Change the cofiguration of the size in your fax machine see if accepts them then

The E 5 error is defined in the User's Manual as: "The FINE Cartridge cannot be recognized. The FINE Cartridge may not be installed properly, or the Cartridge may not be compatible with this machine. Open the Scanning Unit (Printer Cover) and install the appropriate FINE Cartridge."

You mentioned that you have already replaced the Laser Unit, but the error persists. Here are a few more steps you can try: Check the cable: Ensure that the cable connected to the Laser Scanner Unit is properly attached and not damaged. Replace the DC Controller PCB (PCB4): If the error still persists after checking the cable and replacing the Laser Scanner Unit, you might need to replace the DC Controller PCB (PCB4) Here are some YouTubes that may help - once you get past ads. Exciting New Discovery (youtube.com) How to fix error code E110 in Canon ImageRunner Cantina IR 2520 2525 2530 #canon #subscribe (youtube.com)

You can download the Canon printer drivers from their support WEB site. Please click on this link and select your model printer to download : - http://www.usa.canon.com/consumer/controller?act=DownloadIndexAct

If your Canon iPF605 printer won't enter service mode and gets stuck at the "S" symbol without initializing, it may indicate a firmware or hardware issue. Consider updating the firmware or contacting Canon support for further assistance.

They make a few, mains, battery, solar, solar with battery. https://www.google.com/search?q=Canon+Calculator Disconnect power for 30 minutes to reset it. Generic Canon Errors https://www.google.com/search?q=Canon+Calculator+error+message ..

Troubleshoot this issue step by step: Check the Feed Selection Lever: Ensure that the Feed Selection Lever (located on the lower left side of the front of the scanner) is in the correct position (up) for separation. Straighten the edges of the stack of documents to be scanned. Set the document guides so they are wider than the document to be scanned. Place the documents face up into the feed tray, ensuring they touch the document stoppers. Clear Any Jammed Paper: Be careful when removing jammed paper to avoid cuts. Remove any documents that have been left in the eject tray. Close the document eject tray. If the document ejection is stopped partway, perform this operation with the document eject tray extension open. Hold the upper unit as shown in the diagram and open it to the point where you can remove the jammed document. The pickup roller is located in the middle of the upper unit. Do not hold the protrusion on the upper unit when opening it, as it may deform the pickup roller or cause a feeding error. Close the feeder cover. If the jam occurred in the feed section, pull the document out carefully without applying too much force. Be sure to remove any torn parts remaining in the scanner. Close the upper unit slowly, ensuring it clicks into place. Do not force it to close, as this may damage the scanner. After removing the jammed paper, check if the last page was scanned, and then continue scanning. Rapid Recover System: If a paper jam occurs when the "Rapid Recover System" is enabled in the ISIS/TWAIN driver settings, the image of the document is not saved, and scanning stops. You can continue scanning from the document that caused the paper jam after fixing the issue. Additional Considerations: Make sure the pickup rollers retract when the machine is powered on. Check that the stopper plates are in the down position. Verify that the upper unit is completely closed after clearing the jam. Remember to handle the scanner components carefully to avoid damage. If the issue persists, consider seeking professional assistance or contacting Canon support for further guidance