Ricoh Aficio CL7300 DT2 Laser Printer - Answered Questions & Fixed issues

you should go to interface setting and wath your ip . & after connect the lan cable install a tcp/ip device on you're pc and for ip write the ip youhave watched at interface setting .

most likely bad black toner pump. you will need to call a tech is at least a two hour job and you have to take a lot of things out to replace it.

opne then close paper trayy

Look at the transfer unit. If the clear belt has alot of wear lines the belt needs to be replaced pn# B180 3780

The machine builds the alignment image on this belt and then reads it if the belt is cloudy it will fail.

sc 541=Heating roller thermistor error (Fusing unit).
The thermistors could be dirty or damaged.
The fusing unit can be removed and inspected(without removing any screws)(Left door)(lower handle).
If you see any damage you might have to replace the unit(or only the part if u r lucky).

This error is power related... their are two possibilities either... your fuser is blown or your machine needs a reset... here is a link to try the reset...

http://www.fortc.com/2007/06/17/ricoh-cl4000dn-error-code-sc542/

the reset should be all you need...

reset link
I’m happy to assist further over the phone at https://www.6ya.com/expert/norman_d2fa496dce30c65d

If the media (glossy paper) is designed for an ink jet printer you should be fine.

Ink has to be able to be absorbed into the fibers of the page. If you are using paper for a laser color printer, that's your problem.

Don

developer unit not set properly.
push the unit in tight

Ricoh Aficio 240W Plotter Error Code SC 401-00

Copytechnet https://www.copytechnet.com > forums > 108927-rico... May 4, 2016 - On old Ricoh Aficio's SC401 used to be a Transfer error, but on the 240 its ID Sensor, could be dirty, could be old Dev, could be a loose ... Ricoh MP2352 SC401- Strange problem Jul 28, 2021 Error Code SC-401 Sep 12, 2014 ricoh mp 3352 - error sc401 Dec 11, 2020 Ricoh mp 2851 SC 401 Jul 11, 2017 More results from www.copytechnet.com

Error Codes > Ricoh > MP2553 > Code SC401

Printcopy.info https://printcopy.info > code=SC401 Code: SC401 · Description: Transfer positive electrode current error A transfer roller current leak signal is detected. · Causes: • High voltage supply board set ... Missing: W2401 ‎' Show results with: W2401

Error Codes > Ricoh > Aficio 2090 > Code SC401

Printcopy.info https://printcopy.info > code=SC401 Code: SC401 · Description: Transfer roller open error · Causes: • Transfer power pack defective • Poor connection between the transfer current terminal and the ...

If your Ricoh Aficio MP C2800 is showing "toner undetectable" messages for all four toner cartridges and the yellow and cyan colors are not showing up in copies, there may be several potential causes for this issue. Here are some troubleshooting steps to help you resolve the problem:

1. Check Toner Cartridges: Ensure that all four toner cartridges are correctly installed and securely seated in their respective slots. Make sure there are no protective seals or tapes left on the cartridges.
2. Shake Toner Cartridges: Sometimes, toner inside the cartridges can settle or clump, leading to detection issues. Gently shake each toner cartridge side to side to redistribute the toner evenly.
3. Replace Toner Cartridges: If the toner cartridges are old, empty, or expired, replace them with new, genuine Ricoh toner cartridges.
4. Clean Contacts: Dust or debris on the toner cartridge contacts can interfere with communication. Use a soft, lint-free cloth to clean the electrical contacts on both the toner cartridges and inside the printer.
5. Check Developer Unit: The developer unit in the printer plays a crucial role in toner development and transfer. Ensure that the developer unit is clean and free from any obstructions.
6. Perform a Firmware Update: Check if there are any firmware updates available for your Ricoh MP C2800 printer. Updating the firmware might address known issues and improve printer performance.
7. Reset the Printer: Power off the printer, unplug it from the power source, wait for a few minutes, and then plug it back in. Power the printer on to see if the issue resolves.
8. Check Toner Detection Sensors: The printer uses sensors to detect the presence of toner cartridges. Verify that these sensors are functioning correctly and not blocked by any debris.
9. Perform a Factory Reset: As a last resort, you can try performing a factory reset on the printer. However, be aware that this will reset all settings to their defaults, and any custom configurations will be lost

Question edited tor a lot more clarity and add MAKER, but NO MODEL NUMBER! All questions need full make and model.

Ricoh Aficio 200 - Error Code: SC390

PrintCopy .info https://printcopy.info > code=SC390 Code: SC390; Description: TD sensor error 1. The TD sensor outputs less than 0.5V, 20 s after the TD sensor initial setting has been performed. Missing: cod ‎' Must include: cod

SOLVED: How fix sc390 cod of ricoh

Fixya https://www.fixya.com > ... > Ricoh The closest thing is the sc390 code, which means either the toner density sensor or the developer has gone bad, and typically replacing the PCU can fix that ...

• SOLVED: Code SC 390

  https://www.fixya.com > ... > Aficio MP6001 Copier Code SC 390 the code SC390 occurs when power on the machine. ... Service code sc 390 RICO Aficio 1015 coppier ... Sc 390 cod. what this?

Error Code sc 390

Copytechnet https://www.copytechnet.com > 56632-sc-390-a Sep 24, 2011 - I've got an Aficio 1018 that's generating sc390 after every 10 copies. I recently fitted new drum, cleaning blade and developer and changed ... Missing: cod ‎' Must include: cod

• Error code SC 390

  https://www.copytechnet.com > forums > 47571-error... Dear all Experts i often got an error code sc 390 on my ricoh aficio 270.kindly tell me what to do with this problem.

RICOH Error Code List - mtechsinfo.com

mtechsinfo.com http://www.mtechsinfo.com > files > Ricoh Erro... PDF SC-390-2. Toner density sensor error. SC-391. Developer bias problem or FU103 on Aficio 550/650 Image storage address error. Aficio 551, 551P, 700, 700P. 14 pages

Question edited for a lot more clarity and toss in some CAPS. Question moved to maker category. Printer set to wrong size paper. Computer word processing program set to wrong size. For example Letter size paper in Printer and Legal size in the Settings of what is saying to print the document. The paper is too small.

The backup battery for the Ricoh Aficio SP1100sf is located in the control panel. The service manual does not provide specific instructions on how to replace it, but it does provide general instructions on how to maintain and troubleshoot the printer.

replace the polygon mirror motor

hi SOURCE: ricoh aficio 2022 error code sc542 1. Mode(Yellow Button) 2. 107 3. Press STOP Button for 3 second (RED Button) 4. Copy Sp 5. 5810# 6. Excute 7. Power Off 8. Power On

https://printcopy.info/index.php?mod=erc&brand=Ricoh&model=SP100SU&code=SC545

https://printcopy.info/?mod=erc&brand=Ricoh&model=MP1900&code=551

TD sensor (Vt low) error 2: K