20 Most Recent Samsung LE32R41BD 32 in. HD-Ready LCD Television - Page 7 Questions & Answers

There are a number of causes. First The T-Con bd has gone bad. Second the Main bd is bad and third the LCD Panel is bad. Have a trained Samsung tech troubleshoot the problem

is it going up and down the screen? if so, it could be a slight adj, or the lcd panel is going bad. the tv needs to be opened and ebay the physical model of the lcd panel. questions email me

can you u check in the DTB mode, the signal strength & the number ot errors ??

may be you will have to check your antenna connection. Normally it is due to bad signal.

CHECK THE MAIN POWER SUPPLY , either for fuses or replace power supply board. hope it helps , AJ

most probably the inverter board is broken.
please check the inverter board.
if the inverter board works well then it must be the Back light.
thank you.

HI,SOUNDS LIKE YOUR INVERTER PANEL IS GOING,CAN BUY NEW ONE,OR CHECK EBAY FOR GOOD S/HAND ONE,YOU MUST KNOW, WHAT YOU ARE DOING,BEFORE REPAIRING YOUR TV!!!,THANKS

Hi.

Your problem sounds like inverter has failed.
To prove this you need to remove the back from your tv set.
Then switch it on and look carefully through the small holes on the metal shielding that is directly over back of screen you are looking for bright white light.
If you cant see it easily try doing again but in A dark room.
If you can see white light through the holes in metal shielding the inverter is working & fault is else where.
If no light can be seen problem is with inverter you will need to remove the inverter pcb & check the transformers with ohm meter to see if one is open circuit. Allso look on same pcb for any smd circuit protectors that may be open circuit.

http://dysonmanuals.llc.nu/

Chris..

try reversing inputs- DVD into AV-in and sat into component in

I took it back and got a full refund.

WDDW

There's a product called Monster ScreenClean. They are available at places the sell LCD's/Plasma Displays. Not Cheap. $10 buck+.

http://www.monstercable.com/productdisplay.asp?pin=2350

http://www.monstercable.com/productdisplay.asp?pin=4186

http://www.monstercable.com/productdisplay.asp?pin=5096

or you can buy a microfiber towel to just wipe the dust.

Do not use any cleaner solution that is not specifically made for TV monitors (Plasma/LCDs).

Hey this is the wife. Grandson found volume turned off on the cable box and turned it on. End of problem

get a universal remote. follow the ins. for programing that comes with the remote. a radio shack associate can explane it in detail. if you have more problems e me.

Hello, and thank you for choosing FixYa! This could be a smudge, or dust on the color wheel. The area around the lamp needs to be "dusted" Buy a can of compresed air and blow all of the components near the lamp out. You will have to pull the back of the set off to do this. While you are in there you may as well go ahead and blow off the rest of the componenets. Good Luck! If this was usefull, please take a moment and rate this solution!

Usually not but in some cases gently massageing the dot(tv turned on or off try both) with your finger may work (dont push too hard)

or put on a channel with static and try

your chances are slim though this is usually a defect in the lcd technology and most manufactures only warranty it for 5-7 stuck pixels

The Tv is defective. You have to call Corian and get an RM # to return it because it is a defective piece of ****. I had to do the same thing and just spent $33.00 to ship it back to California. They have no idea when I will get a new TV or waht kind it will even be.

Try unplugging the TV and give it a minute or so, then plug it back in. Sometimes the computer inside gets wonky. Completely removing power will reset it, but just turning it off and on doesn't change anything.

If there is still no signal, verify that the source is actually functioning and that all your connecting cables are still firmly in the right places.