Samsung LN-S4092D 40 in. LCD HDTV - Page 2 - Answered Questions & Fixed issues
Weak or no signal message
- Since my problem (Samsung/Comcast) began with a channel selection button pushed on the TV remote when it should have been pushed on the cable remote, I figured the problem lay with the TV. Although I was getting the "weak or no signal" msg., the actual signal strength bar graphic showed it to be strong. Disconnecting did no good. I surmised that the TV was simply not recognizing the box.
- I looked at the manual for my Samsung 750 model.
- Page 20 discussed "Selecting the source". I accessed the TV menu and selected "Input", then chose the "HD..." item from the highlighted list. Voila! My tv works again.
12/22/2012 6:13:27 PM •
Samsung...
•
Answered
on Dec 22, 2012
•
15,267 views
Hey there
There are many possibilities like...
Select switch can be defective and sends un necessary command to system control IC.
System control board can have dry solder joints or lose connections etc.
9/26/2008 5:15:45 PM •
Samsung...
•
Answered
on Sep 26, 2008
•
51 views
Picture Size
Also, try adjusting the settings on your cable box, not on the TV. The usually solves the problem and will then allow you to adjust the size of the picture.
10/7/2008 1:08:40 AM •
Samsung...
•
Answered
on Oct 07, 2008
•
1,007 views
LCD TV
I had a problem with a Samsung 46 inch LCD and it had audio and dim light but no picture and found out that the logic board toward the top (inside tv) was bad and was no longer available and the only way to fix it was to get the entire display panel (the logic board came with it) It was not costwise to repair. Hope this helps.
11/30/2008 3:16:05 AM •
Samsung...
•
Answered
on Nov 30, 2008
•
624 views
Picture Size
please provide the maker & the model & part # of your unit..
Thank you
5/2/2008 12:49:21 PM •
Samsung...
•
Answered
on May 02, 2008
•
436 views
Actually it a lnt5271f, but...
there is a differnece between other TV's in the house working and the TV at that specific location working. Check the cable splitters which go into that room and tighten the cables at all ends..loose/broken cables cables can result in weak signals. It might be a bad splitter too.
5/29/2008 4:13:18 AM •
Samsung...
•
Answered
on May 29, 2008
•
121 views
Samsung LNS4041D has picture goes off
Try to turn off, pull power cable out wait for a while then back power cable and turn power ON! If nothing happen power adapter must be changed!
1/29/2008 6:33:00 PM •
Samsung...
•
Answered
on Jan 29, 2008
•
219 views
No picture
IF THERE IS NO PICTURE YOUR TV HAS BEEN SET TO A DIFFERENT RESOLUTION THAN WHAT IS COMING IN
3/15/2009 1:03:08 AM •
Samsung...
•
Answered
on Mar 15, 2009
•
217 views
Problem with 1080p via hdmi?
are you hooking up a 1080p source..if not then the set will not display the best picture in 1080p mode..
12/1/2007 2:05:09 PM •
Samsung...
•
Answered
on Dec 01, 2007
•
311 views
Home theator system will not work
the hdmi connector on the tv has probably pulled loose from the main board..they are not attached very securely..it might be possibe to resolder..
12/1/2007 12:14:47 PM •
Samsung...
•
Answered
on Dec 01, 2007
•
74 views
PC to TV Picture
try a DVI/digital cable on the HDMI inputs
4/30/2007 12:40:08 AM •
Samsung...
•
Answered
on Apr 30, 2007
•
178 views
One side of my tv gets dim and out of focus it is a samsung. At times it works fine
back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis.
http://electronicshelponline.blogspot.com/ To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced. To some models of sets, all these section circuit will be integrated at its main board. If this is the case, you have to replace the main board.
11/18/2016 3:00:54 AM •
Samsung LN...
•
Answered
on Nov 18, 2016
•
180 views
How do I troubleshoot my Samsung TV?
I have sound, but no picture.
Caps can fail with no outward signs. It takes a special meter to test them. Your set may have a back light inverter that powers the back lights. When it fails, the picture cant be seen, but you have sound, to check this look for a picture on the screen using a flashlight
3/17/2016 10:45:02 PM •
Samsung LN...
•
Answered
on Mar 17, 2016
•
683 views
My Samsung Tv modle LN46C600F3F has sound no picture, what could be wrong?
Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis.
http://electro-medical.blogspot.com/
http://electronicshelponline.blogspot.com/
To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced.
1/18/2016 3:39:48 AM •
Samsung LN...
•
Answered
on Jan 18, 2016
•
329 views
Increase brightness in samsung tv
Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis.
http://electronicshelponline.blogspot.com/
In some models of LCD TVS; the backlight inverter and its T'Con board will be a part of the panel itself, and will be a built-in type inside the LCD panel. If so, they can't be replaced. In this case; a panel replacement is the only repair. For some other models, the backlight inverter section circuit will be a part of the main power supply regulator [SMPS]. To such sets, the power supply section circuit too should be troubles hooted. Contact any service technician. The circuit will differ with models and versions.
Type in the brand name of your device, in the search box [at the top right] of the display window and the Search will start at once as you type in, and will show you all the related posts. It will make surf easy.
3/15/2015 9:37:35 AM •
Samsung LN...
•
Answered
on Mar 15, 2015
•
143 views
Not finding what you are looking for?