Alpine CDA-9857 CD Player - Answered Questions & Fixed issues

The deck might be damaged. In order to accommodate that kind of layout, there should be a cross over, and a separate 2 channel amplifier for the subs. Without that it's easy to fry the deck!

Are you running your audio through an amplifier? If you are, it sounds like you are using the blue wire (power antenna remote turn on) instead of the blue/white (amplifier remote turn on). The blue wire shuts off when you leave tuner mode, thus turning your amp off.

the best way to get it out is to take the deck apart if you can see th cd try tweezers or needle nose id bet there is more than one in it i hope this helps

Probably you dont have the constant pos (+) wire hooked up to hot (+) wire and only to a source that is switched. Switched means every time your key is removed from ignition switch the positive current from that source will also power down. There are two positive leads from the unit, 1 always hot and the other needs to be switchable. The constant hot (usually yellow) powers the memory for your settings. Just like your television set, once you pull the cord off the socket everything returns to default setting.

here's your best start...
jump on eBay and type in your model number: CDA-9857

Lots of the ipod input adapters out there on eBay.
The adapters hook up to the back of the Alpine CDA-9857 deck.

The display can be blacked out on the 9857r. To toggle between display on and display off hold the function button until it beeps.

Sounds like you have a bad connection somewhere. pull the radio out and check your power and ground connections to ensure that they are tight.

Please see my solution posted on Mar 13. No other brain waves yet!

Users manual is HERE.

The Constant +12 volt wire is the yellow one. Wiring connections begin on page 34.




Best of Luck.

my alpine cda 9856 only displays that message when my ipod dies. so your ipod pobably dies then the head unit recharges it enough in the time your resetting it that it can play again. :)

You can't use search mode while you have mix enabled. Make sure Mix mode is off

You have the amp hooked to the "Antenna turn on" which is the blue wire.... you need to hook it to the "REM" output whis is Blue with a white stripe.

You can download the manual from the link below: http://vault.alpine-usa.com/products/documents/CDA-9857%20OM.PDF Please update the question & let us know if the information given was useful to you - Good Luck!

Check the pink wire at the back of the deck. It shouldn't be connected to anything, and you need to make sure it isn't pinched or shorted. "INTERUPED" means that the deck thinks that it's connected to a hands-free kit for a wireless phone, and that you're receiving a call. The pink wire is the interface wire for that type of system.

You need to purchase a 30 (thirty) dollar cable from best buy. Mike

1. Mechanical Issue: There might be a mechanical problem with the disc drive or the eject mechanism. It's possible that a part is jammed or not functioning correctly.
2. Dirty or Damaged Disc: If the disc is dirty, scratched, or damaged, the player may have difficulty reading it and thus not ejecting it properly.
3. System Error: There could be an internal error within the player's software or firmware causing it to not recognize the disc properly or to malfunction when attempting to eject it.
4. Power Issue: Sometimes, power-related issues can affect the functionality of electronic devices. Ensure that the player is receiving adequate power and there are no loose connections.

Here are some troubleshooting steps you can try:

• Turn off the player and then turn it back on to see if it resolves the issue.
• Try ejecting the disc using the manual eject button (if available). This button is usually a small pinhole near the disc slot. You can insert a paperclip or a similarly sized object into the hole to manually eject the disc.
• If possible, try using a different disc to see if the problem persists. If other discs work fine, then the issue may be with the original disc.
• Check for any visible obstructions around the disc slot and remove them if present.
• If none of the above steps work, you may need to contact Alpine customer support for further assistance or consider taking the player to a qualified technician for repair.

Se o Bluetooth do seu Alpine CDE-W235BT parou de funcionar ap?s uma falha durante a atualiza??o, pode haver algumas etapas que voc? pode tentar para resolver o problema: 1. **Reinicie o Aparelho:** - Desligue o r?dio por alguns minutos e ligue-o novamente. Isso pode reiniciar o sistema e resolver problemas temporariamente. 2. **Restaurar as configura??es de f?brica:** - Consulte o manual do usu?rio para descobrir como realizar uma restaura??o das configura??es de f?brica em seu Alpine CDE-W235BT. Isso pode resolver problemas causados por configura??es incorretas. 3. **Verifique a vers?o do firmware:** - Se poss?vel, verifique a vers?o do firmware do seu Alpine CDE-W235BT. Se houver uma vers?o mais recente dispon?vel, considere atualizar novamente o firmware, seguindo rigorosamente as instru??es do fabricante. 4. **Remova Dispositivos Pareados:** - No menu Bluetooth do r?dio, remova todos os dispositivos pareados anteriormente e, em seguida, tente parar novamente. ?s vezes, problemas de conectividade podem ser resolvidos removendo e pareando novamente os dispositivos. 5. **Atualiza??es de Software:** - Verifique se h? atualiza??es de software dispon?veis para o seu Alpine CDE-W235BT no site do fabricante. Caso existam, siga atentamente as instru??es para realizar a atualiza??o. 6. **Contate o Suporte T?cnico:** - Se as solu??es acima n?o resolverem o problema, entre em contato com o suporte t?cnico da Alpine. Eles podem fornecer assist?ncia espec?fica para o seu modelo e orienta??es adicionais para resolver o problema. Lembre-se de que mexer no firmware e nas configura??es do dispositivo envolve riscos, e ? sempre recomend?vel seguir as instru??es fornecidas pelo fabricante para evitar danos permanentes ao aparelho. Se voc? n?o se sente confort?vel fazendo isso por conta pr?pria, procurar ajuda profissional pode ser uma op??o.

Question edited for clarity. https://www.google.com/search?q=alpine+vie-x077+wiring+diagram https://www.google.com/search?q=alpine+vie-x077+installation+manual ..

After researching, it appears that there is no direct evidence suggesting that the Alpine TDM 7543 stereo unit has the ability to switch from green to red lighting. This is an older unit and specific information can be challenging to find. Your best option to get a definitive answer may be to directly contact Alpine's customer service or refer to the original instruction manual.

Help here https://www.google.com/search?q=hange+the+language+of+my+alpine+car+stereo+(700w)+to+English ..