Konica Minolta PRINTING - Bizhub-250 Minolta 25ppm Printer/Copier/Scanner/Fa - Page 2 - Answered Questions & Fixed issues

Replace the black image unit not toner

What is the model number? Ball park! replace the black developer unit and black drum

What is the model number?

Would help to know the model of the machine

Replace the transfer belt.

Remove the paper behind the paper draws

Konica Minolta Bizhub C266 MFP PCL6 Driver 7.2.0.0 so what PC is it.? non told what OS on PC windows 7 to 11? connected via USB?????? that means the PC driver is bad, wrong or missing In what country are you. the UK drivers are at makers sites, but sites are by country so... why not ask maker for direct support and not use virus infected drives I see google finding endless now. direct from them on there specific website for your COUNTRY UK https://www.konicaminolta.co.uk/en-gb/support/customer-support

get it serviced (call) or RTM< the RTM read the service manual end.

Question edited for spelling and full 'make model (what it is)'. Please don't type in all CAPS, it is considered SHOUTING and is hard to read. Question moved from Cellphones category. Check out the videos https://www.google.com/search?q=KONICA+MINOLTA+c360+disable+drawer+2 ..

Try Reset, or call for service. https://www.google.com/search?q=Bizhub+951+reset ..

Check the link https://www.google.com/search?q=konica+minolta+bizhub+c224e+black+not+detected ..

C-2451 to C-2453 error codes are lit even if the Developing Unit, developer, and Charging Unit are replaced. This is a symptom from a customer who mostly prints black. If you increase toner density, it will be good.

Actually C8101 is on Rank B meaning by Open / Close the front door to clear it. But if error code still appear, Check the connector between M3-relay CN5-DFCB J15 for proper connection and correct as necessary. Check the connector between PS12-DFCB J15 for proper connection and correct as necessary. Check the connector of M3 for proper drive coupling,and correct as necessary. PS12 I/O check, sensor check M3 operation check (change M3) DFCB F8 conduction check

https://printcopy.info/?mod=erc&brand=Konica-Minolta&model=bizhub+C368&code=C2552%2C+C2554

Estimated abnormal parts: • Fusing unit • Printer control board (PRCB) • AC drive board (ACDB) • Fusing heater lamp /1 (L2) • Fusing heater lamp /2 (L3) • Fusing heater lamp /3 (L4) • Temperature sensor /1 (TH1) WARNING • After replacing the defective parts, be sure to set the DIPSW 3-1 to 0. If DIPSW3-1 is set to 0 before defective parts are fixed, it may cause fire. Solution 1. Check the connection between the rear side connector of the fusing unit and the main body side connector, and repair it if any abnormality. 2. Check the connector connection and the wiring between PRCB and the temperature sensor, and repair it if any abnormality. 3. Check the connector connection and the wiring between ACDB and the fusing heater lamp, and repair it if any abnormality. (Wiring diagram: Main body (1/3): 3-E) 4. Check the installation condition of the fusing heater lamp and ON/OFF with I/O, and repair/replace it if any abnormality. (Wiring diagram: Main body (1/3): 3-D) 5. Check the installation condition of TH1 and temperature of I/O, and adjust/replace it if any abnormality. (Wiring diagram: Main body (1/3): 3-F) 6. Replace TH1. 7. ReplaceL2, L3 and L4. 8. Replace ACDB. 9. Replace PRCB.

Replace the ink cartridge.

https://www.manualslib.com/manual/1250645/Konica-Minolta-Bizhub-C360.html?page=652&term=CC172&selected=2#manual

Level Adjustment error. Has the drum and the developer unit and developer been replaced? Has the drum unit/assy. been cleaned including the sensor!!!!!!!!!

alignment in regards to what Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f