AEG 24 in. Favorit 40650 Free-Standing Dishwasher - Answered Questions & Fixed issues
I have triggered the anti
When this happened to ours it was food debris in the water supply feed. There is a tank located in the left hand side wall which is accessed by taking the side off the machine. This tank needs to be replaced as although it may reset itself a few times the problem continue to occur until the water fill path is clear
3/2/2014 8:35:34 PM •
AEG 24 in....
•
Answered
on Mar 02, 2014
•
6,108 views
Water not draining even after clean
The dishwasher has an outlet pump in line with the outlet hose. This pump must work in order for the washer to drain. The pump can be tested by unpluging it and removing the 2 hose clamps. Connect the pump to the mains for a few seconds and it should spin the impeler. The impeler must rotate a a speed and must not be obstructed in any way. If this does not spin the outlet motor it should be replaced.
1/20/2010 1:32:57 PM •
AEG 24 in....
•
Answered
on Jan 20, 2010
•
394 views
Access to flow thru heater
On the 40660 washer this element is in line with the top sprayer arm pipe and is at the back bottom of the washer. Easly reachable by removing the back bottom plate. Has a clamp on each end and a electrical push on connector.
1/20/2010 10:26:55 AM •
AEG 24 in....
•
Answered
on Jan 20, 2010
•
363 views
AEG Favorit 40650 water heater not working
Check the element by using an Ohm meter. You should get an ohm reading if the element is OK. If the element is open circuit you would get an infinity reading. Just note that "newer" machines do not use the traditional heating elements but do have a (Inductive heater) coupled in line with the hose feeding the top spray arm of the washer. This unit must be cheched by a dealer as a DIY will have dificullty checking it.
1/19/2010 9:10:16 AM •
AEG 24 in....
•
Answered
on Jan 19, 2010
•
1,080 views
Dishwasher AEG FAV40620W stuck time delay
Thanks. I figured it out from the online manual. Hold buttons #2 and
#3 (second and third button down on far left side) for 2 seconds should
reset it. It took some 15 minutes however before the dishwasher reset!
Peter Smith
1/28/2009 9:38:28 AM •
AEG 24 in....
•
Answered
on Jan 28, 2009
•
2,612 views
AEG FAVORIT 35085 Vi dishwasher Beeps 5 times and stops
If your AEG FAVORIT 35085 Vi dishwasher beeps five times and stops halfway through a wash cycle, there could be a few potential causes for this issue. One possibility is that there is a problem with the water supply, such as a clogged or partially blocked inlet valve. Another potential issue could be related to the drainage system, such as a clogged filter or a malfunctioning drain pump. It's also worth checking if the dishwasher's spray arms are spinning freely and not obstructed by any debris. If the problem persists, it is recommended to consult the dishwasher's manual or contact AEG's customer support for further assistance. They can provide specific troubleshooting steps and guidance based on your dishwasher's model and any error codes that may be displayed.
6/18/2023 12:27:47 PM •
AEG Dishwashers
•
Answered
on Jun 18, 2023
•
117 views
The anti flood device has activated on my AEG dishwasher????
If the anti-flood device has activated on your AEG dishwasher, it means that water has leaked into the base of the dishwasher and triggered the safety device. The anti-flood device is designed to prevent water damage to your home and shut off the water supply to the dishwasher.
To resolve this issue, you will need to locate the source of the leak and fix it. Here are the steps you can take:
- Turn off the dishwasher and unplug it from the power outlet.
- Disconnect the dishwasher from the water supply and move it away from the wall.
- Check the inlet hose, outlet hose, and drainage hose for any cracks, damage, or loose connections. Tighten any loose connections and replace any damaged hoses.
- Check the dishwasher door and gasket for any damage or debris that may prevent it from closing properly.
- Check the dishwasher's interior for any leaks, such as a cracked spray arm or a damaged pump.
- Once you have fixed the leak, you can reset the anti-flood device by tilting the dishwasher to one side to allow the water to drain out of the base. Then, level the dishwasher and plug it back in.
If you are unable to identify or fix the leak, it is recommended to call a professional technician for assistance.
2/24/2023 10:09:41 PM •
AEG Dishwashers
•
Answered
on Feb 24, 2023
•
355 views
My AEG F86070VI dishwasher wont switch on
Did you check the emergency shut off switch? Almost all under the counter dishwashers have a wall switch to interrupt the power. The problem is it can be shut of on accident.
10/11/2022 8:52:22 PM •
AEG Dishwashers
•
Answered
on Oct 11, 2022
•
64 views
Why is the timer light and alarm still sounding in my dishawasher?
I would check for any bends in anything... a crimp of a wire or bend of a hose can mean the washer will not complete setup and will just refuse like a stubborn mule. If you find no bends or crimps in wires... the brain may be dead. It will be one solid motherboard and should be fairly easy to replace.
2/23/2022 4:26:38 PM •
AEG Dishwashers
•
Answered
on Feb 23, 2022
•
84 views
AEG dishwasher draining too early / unexpectedly
The hose could be clogged or an issue with the valve assembly.Or something being stuck in the inlet water valve. Check to see if there is any problems coming from where the water enters into the tub for your dishwasher mostly on the left side wall of the tub on your dishwasher.
10/12/2021 4:40:49 PM •
AEG Dishwashers
•
Answered
on Oct 12, 2021
•
208 views
Not finding what you are looking for?