20 Most Recent AEG Favorit 50500 Built-in Dishwasher - Page 2 Questions & Answers

Did you check the emergency shut off switch? Almost all under the counter dishwashers have a wall switch to interrupt the power. The problem is it can be shut of on accident.

Look at the screen on the drain.if its clear then check your drain for leaks
As it could be building pressure on the system..by not draining proper.

If you are reading this, then you probably own an AEG dishwasher with a ceiling arm. This part is important for the dishwasher to function properly and needs to be cleaned regularly. However, if it becomes loose or falls off, it can be a real headache to try and reattach it. In this article, we will walk you through the process of how to fix a ceiling arm back onto your dishwasher.

I would check for any bends in anything... a crimp of a wire or bend of a hose can mean the washer will not complete setup and will just refuse like a stubborn mule. If you find no bends or crimps in wires... the brain may be dead. It will be one solid motherboard and should be fairly easy to replace.

Question edited for clarity. Question moved from Washing Machines category. That sounds like a partially broken wire or a control board issue. You need a service call.

possibly a stuck float

USUALLY IN THE WATER PAN

The hose could be clogged or an issue with the valve assembly.Or something being stuck in the inlet water valve. Check to see if there is any problems coming from where the water enters into the tub for your dishwasher mostly on the left side wall of the tub on your dishwasher.

Some companies share generic codes like 'Lw', for low water level or 'DL' for Door Lock. This might help, there are other sites when Googling 'make model error codes'.

AEG Dishwasher Error Codes ' Dr. Dishwasher

www.drdishwasher.com > manufacturer > error-codes

Error/Fault Codes for AEG Dishwashers with an LED Display Fault Code ,10 Symptom: Dishwasher not filling with water. Go to: Why is My Dishwasher Not Filling ...

You can test the element which is the most likely failure, but you need a multimeter set to ohms (resistance). An element is a coil that resists electricity and heats up. You disconnect the leads to the heater element and it should show resistance, movement on the dial or a figure on a digital multimeter. If the element has failed, there will be no reading at all. If it worked before, it will be probably be worth fixing, but don't just blindly buy parts in the HOPE it might fix it. Diagnose and replace, or call a service tech. https://www.google.com/search?q=Aeg+favorit+FSS62800P ..

http://www.usersmanualguide.com/aeg/dishwasher/favorit_525_u https://www.manualslib.com/manual/44456/Aeg-Favorit-Compact-525i.html AEG Favorit Compact 525i Operating Instructions Manual

We had this a while back on ours. For us it meant that the flood prevention system had kicked in. I took the metal panel at the bottom at the front off and sucked out water with a syringe until it started working again. We think the problem was that something was blocked with grease so ran a hot cycle with a Finish cleaning cartridge in.

Google or request from manufacturer

I guess you got the alarm AL 6 on your display what means failure to drain. A control procedure has been added to all the final drain phases in order to check the status of the pressure switch. The contact must be open in the "empty" position in order to ensure that the cycle is performed correctly. If the contact is closed, the drain phase is repeated. At the end of the second drain phase, if the pressure switch contact remains closed, "AL" alarm condition is generated. Could be following:

• Domestic drain circuit not suitable (obstructed / blocked)

• Drain pump jammed

• Pressure switch faulty

• Sump - pressure switch tube obstructed

• Filters / drain hose obstructed

• Relay or Triac faulty

Down under is from AEG Favorit 86460 user manual, page 30 : ...a flashing fault code appears an audible signal informs you that an alarm has been activated, in the display appears one of the following flashing alarms: AL1 - AL2 - AL3 - AL4 - AL5 - AL6 - AL7, AL8 and the indicator light of the phase under way is flashing. They are indicative of a fault in the dishwasher that you can probably rectify yourself. - press the On/Off push button to switch the dishwasher off - open the door and carry out the following suggested corrective actions. Dado

https://youtu.be/96x4TUUyeJ4 Try this buddy

check the sum pump drian valve make sure it not cog up with tash because if it block can cause the drain pump to ruin ok

Owner's manual should have a troubleshooting section. Canal? you may have a serious leak in fill piping or control valves. or drain system. No owner's manual? Try MFG website or http://www.manualsonline.com/

Is it not hide in the big pumphose?