20 Most Recent
AEG 24 in. Favorit 60830 Free-standing Dishwasher - Page 6 Questions & Answers
How do I fix problem F3 and spray arm faulty on my KO FAVORIT 8080
F3 - The anti-flood protection system has activated.
When in operation the fault message F3 appears in multi dispay:
- First close the water tap.
- Pull out the power plug.
- In the case of hard-wiring: turn off the electricity supply, remove the fuse and disconnect.
- Check float microswitch and float of styrofoam.
- Find and remedy water lakeage in the bottom of dishwasher.
Dado
How do I fix problem F3 and spray arm faulty on my KO FAVORIT 8080
F3 - The anti-flood protection system has activated.
When in operation the fault message F3 appears in multi dispay:
- First close the water tap.
- Pull out the power plug.
- In the case of hard-wiring: turn off the electricity supply, remove the fuse and disconnect.
- Check float microswitch and float of styrofoam.
- Find and remedy water lakeage in the bottom of dishwasher.
Dado
AEG OKO FAVORIT 40300 When switching dishwasher on no water is flowing into the the dishwasher?
It should first be checked for correct water inlet hose with safety valve. After connecting the double-walled water inlet hose, the safety valve is next to the tap. Therefore the water inlet hose is only under pressure while the water is running. If the water inlet hose starts to leak during this operation,
the safety valve cuts off the running water and the draining pump in the dishwasher is switched on. If the inlet hose with safety valve working correctly than could be some of following faulties.
- The door of the dishwasher is not closed properly.
- Mains plug is not plugged in.
- House fuse in defective.
- In the case of dishwasher models with start delay
timer: A start delay is selected.
If you look at the lower electrical diagram then you can see that all electrical components are located in a circuit inlet valve which can be also faulty.
- ON/OFF Switch
- Door switch
- Program controller (Timer)
- Pressure switch
- Inlet valve
- Float switch
- Wiring between all this components
Dado
How do I fix error .60?
The temperature must increase by a certain amount at each step.
If there is no temperature increase, the electronics will generate "Heating Time Out" or fault code i60.
In this case program will continue to the end without heating and the washing result will probably be unsatisfactory.
Could be: Heating element faulty; intervention of safety
thermostats (open); faulty wiring; NTC sensor (poor
thermal contact); insufficient water circulating in the
tub; washing faulty pump (impeller stripped); circuit
board faulty.
Dado
What means error .60?
The temperature must increase by a certain amount at each step.
If there is no temperature increase, the electronics will generate "Heating Time Out" or fault code i60.
In this case program will continue to the end without heating and the washing result will probably be unsatisfactory.
Could be: Heating element faulty; intervention of safety
thermostats (open); faulty wiring; NTC sensor (poor
thermal contact); insufficient water circulating in the
tub; washing faulty pump (impeller stripped); circuit
board faulty.
Dado
I have a oko favorit 4071 doesnt start and display H8 error.
I think this is not the error code. I belive this is hardness of water (could be set from 0 or 1 to 10, depending of model. Read your user manual how to exit the program for adjust the water hardness).
Error code for your appliance depending on model and look like:
i10, i20,i30............ or
C1, C2,C3.............
Dado
Why my AEG F55080vi stops after drain cycle (program beginning) and then it stops and I hear 2 beeps and 2 flash continuously?
Definitely, water drain time-out. Error code i20.
The pressure switch doesn't return to EMPTY (1-2) after two drain phases lasting 120 seconds.
Possible causes:
Drain circuit obstructed/blocked; drain pump
interrupted or jammed (foreign bodies); level
pressure switch blocked on FULL (1-3); hydraulic
circuit of pressure switch obstructed; wiring faulty;
circuit board faulty.
Thanks to your detailed description of failure I conclude that in drain phase (after starts drain pump) leaks water and causing a short circuit. I would thoroughly reviewed drain hydraulic circuit. If is alarm displayed and there is no water inside dishwasher then check heater and anti-interference suppressor.
Dado
AEG 50879
This option can be selected by pressing the corresponding button, and remains in memory until the same
button is pressed again. This option modifies the phases of the programme in order to optimize performance
when "3 in 1, 5 in 1, 7 in 1, ......." detergent tablets are used:
- variation of the duration of the programme and the temperatures required to dissolve the detergent tablets.
- reduction of water exchange
- exclusion of introduction of rinse-aid
- exclusion of regeneration
If you use a dishwasher in the traditional manner (detergent, rinse aid, salt) then the Multitab function is disabled. If you use tabs that are already on the market with rinse aid and salt there is a possibility during washing cycle to add a double dose of rinse aid. From rinse aid dispenser and rinse aid from tabs. This will lead to poor cleaning results, glasses will look like they have been washed in milk..To avoid that you must turn on "Multitab" function and thus exclusion of introduction of rinse-aid from rinse aid dispenser. This function also stops the regeneration and will not spend salt because salt is already in a tabs. Also extends the washing time because tablets need more time to dissolve in relation to the traditional powder detergent.
Dado
Water not heating! is it element? how do i get to it?
The easiest way is the system of elimination. Professional way by measuring the resistance, current and voltage.
Could be: faulty power board (completly or only relay for heating element), faulty wiring between heating element and power board, faulty heating element (interruption, short circuit or current leakage,on some heaters faulty thermal protection)
Dado
I have a AEG F88060VIOP dishwasher - showing error coded ,00 and beeping. Not listed in manual - can anyone help id cause and fix please? Thanks
Fault code "i00" means "Low mains voltage"
The electronic board makes sure the dishwasher operates within certain voltage limits. If during a cycle the voltage drops below the lowest limit, the electronic board suspends all loads and interrupts the cycle under way. The "i00" alarm is then triggered. The lowest main voltage threshold is 180 Volt. If the voltage goes back to over 186 Volt, the electronic board cancels the error status and the cycle
resumes. The "i00" alarm is also deleted.
If the mains voltage continues to exceed the maximum threshold, the electronic board does not do anything.
My suggestion is to call your local electrician to check the voltage in your home.
Dado
Dishwasher no circulation
Hi
Now you said it won't circulate when it gets to this point can you put your hand on unit and feel it vibrating like the motor is trying to run if so you have something in sump area jamming it. Remove foreign object. If it does not vibrate then you may have a bad motor or main board. To test if you know electronics look at board and find connection for motor and check if you get 120V if so then either bad motor or stuck. Good Luck
How to fix a c2 error message on an aeg dishwasher?
C2 error may indicate a pump problem or too slow pump action this may be due to a blockage in the pump or a failed or failing pump capacitor this is not an expensive fix look for a replacement capacitor on Maplins of uk white goods web site you can get the size from the details on printed on the capacitor.
Not finding what you are looking for?