AEG 24 in. Favorit 80860iW Built-in Dishwasher - Answered Questions & Fixed issues

Activated Anti-flooding system, means water leakage in the buttom of dishwasher. Could be also: faulty Anti-flooding microswitch, floating sensor (styrofoam) blocked mechanically, wiring diagram, electronic. Dado

Hi, I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works like new... However I have also foundthat if the heating element goes bad then that also can mess things up bad...So I would buy new spray arms, and also check out the heating element to makesure it is working... Here is a tip that will help you with the onlinebuying...
Dishwasher SprayArms not Spinning

How to Buy ApplianceParts Online

A bad heating element causes many problems in dishwashers...

Dishwasher Problems The HeatingElement not Working

DishwasherMaintenance DishwasherResidue and Film on Dishes

heatman101

Asker's Testimonial "explanation very clear. will give it a go and see howsimple it was. thanks Ronnie " - ronnieshomes

; ';'; ;

Open the left metal panel, if the white plastic tank is black at the bottom or is not clean: remove it, open it, clean it (make sure the water flows through properly) and put it back in.

Check water pump inside the machine for its full speed.If the speed is low check the capcitor and replace.

This does sound like a problem with the "anti-flood" device that does detect water (leak / spill) at the base of the washer. This device is a protection device that consists of a polystirene float and a micro swithch. Once a water leak od spill is detected it automatically puts the washer in pump out mode. You need to determine if a leak exists that has caused the float to trigger the micro switch and clear the water / leak. This should put the washer back to normal.
However if the senslogic (pc board) has a program fault, the cost of this board = half the cost of a new washer ......

This is caused by a partially blocked valve or inlet, it is a little blocked, and this sound you hear is the air pushed through it making a sound. You need to clean out the inlet valves.

http://www.nodevice.com/user_manual/aeg/dishwasher/f80860i-m_911234717.html
User manual.

Question edited for clarity. It is likely to be a control board issue. They are expensive, so call for diagnostics and service. The reason the dishes aren't clean is because it is stuck on wash, so there is no draining and rinses. This machine has some history! https://www.google.com/search?q=aeg+f34300vi0+dishwasher+keeps+running ..

If your AEG FAVORIT 35085 Vi dishwasher beeps five times and stops halfway through a wash cycle, there could be a few potential causes for this issue. One possibility is that there is a problem with the water supply, such as a clogged or partially blocked inlet valve. Another potential issue could be related to the drainage system, such as a clogged filter or a malfunctioning drain pump. It's also worth checking if the dishwasher's spray arms are spinning freely and not obstructed by any debris. If the problem persists, it is recommended to consult the dishwasher's manual or contact AEG's customer support for further assistance. They can provide specific troubleshooting steps and guidance based on your dishwasher's model and any error codes that may be displayed.

If the anti-flood device has activated on your AEG dishwasher, it means that water has leaked into the base of the dishwasher and triggered the safety device. The anti-flood device is designed to prevent water damage to your home and shut off the water supply to the dishwasher. To resolve this issue, you will need to locate the source of the leak and fix it. Here are the steps you can take:

1. Turn off the dishwasher and unplug it from the power outlet.
2. Disconnect the dishwasher from the water supply and move it away from the wall.
3. Check the inlet hose, outlet hose, and drainage hose for any cracks, damage, or loose connections. Tighten any loose connections and replace any damaged hoses.
4. Check the dishwasher door and gasket for any damage or debris that may prevent it from closing properly.
5. Check the dishwasher's interior for any leaks, such as a cracked spray arm or a damaged pump.
6. Once you have fixed the leak, you can reset the anti-flood device by tilting the dishwasher to one side to allow the water to drain out of the base. Then, level the dishwasher and plug it back in.

If you are unable to identify or fix the leak, it is recommended to call a professional technician for assistance.

no info generic answer inlet valve failure --short in valve circuit

Did you check the emergency shut off switch? Almost all under the counter dishwashers have a wall switch to interrupt the power. The problem is it can be shut of on accident.

Look at the screen on the drain.if its clear then check your drain for leaks
As it could be building pressure on the system..by not draining proper.

If you are reading this, then you probably own an AEG dishwasher with a ceiling arm. This part is important for the dishwasher to function properly and needs to be cleaned regularly. However, if it becomes loose or falls off, it can be a real headache to try and reattach it. In this article, we will walk you through the process of how to fix a ceiling arm back onto your dishwasher.

I would check for any bends in anything... a crimp of a wire or bend of a hose can mean the washer will not complete setup and will just refuse like a stubborn mule. If you find no bends or crimps in wires... the brain may be dead. It will be one solid motherboard and should be fairly easy to replace.

Question edited for clarity. Question moved from Washing Machines category. That sounds like a partially broken wire or a control board issue. You need a service call.

possibly a stuck float

USUALLY IN THE WATER PAN

The hose could be clogged or an issue with the valve assembly.Or something being stuck in the inlet water valve. Check to see if there is any problems coming from where the water enters into the tub for your dishwasher mostly on the left side wall of the tub on your dishwasher.

Some companies share generic codes like 'Lw', for low water level or 'DL' for Door Lock. This might help, there are other sites when Googling 'make model error codes'.

AEG Dishwasher Error Codes ' Dr. Dishwasher

www.drdishwasher.com > manufacturer > error-codes

Error/Fault Codes for AEG Dishwashers with an LED Display Fault Code ,10 Symptom: Dishwasher not filling with water. Go to: Why is My Dishwasher Not Filling ...