20 Most Recent AEG 24 in. Favorit 50730W Free-standing Dishwasher - Page 7 Questions & Answers

The easiest way is the system of elimination. Professional way by measuring the resistance, current and voltage. Could be: faulty power board (completly or only relay for heating element), faulty wiring between heating element and power board, faulty heating element (interruption, short circuit or current leakage,on some heaters faulty thermal protection) Dado

Fault code "i00" means "Low mains voltage" The electronic board makes sure the dishwasher operates within certain voltage limits. If during a cycle the voltage drops below the lowest limit, the electronic board suspends all loads and interrupts the cycle under way. The "i00" alarm is then triggered. The lowest main voltage threshold is 180 Volt. If the voltage goes back to over 186 Volt, the electronic board cancels the error status and the cycle resumes. The "i00" alarm is also deleted. If the mains voltage continues to exceed the maximum threshold, the electronic board does not do anything. My suggestion is to call your local electrician to check the voltage in your home. Dado

The temperature must increase by a certain amount at each step. If there is no temperature increase during three minutes, the electronics will generate "Heating Time Out" or fault code i60. In this case program will continue to the end without heating and the washing result will probably be unsatisfactory. Could be: Heating element faulty; intervention of safety thermostats (open); faulty wiring; NTC sensor (poor thermal contact); insufficient water circulating in the tub; washing faulty pump (impeller stripped); circuit board faulty. Dado

Hi Now you said it won't circulate when it gets to this point can you put your hand on unit and feel it vibrating like the motor is trying to run if so you have something in sump area jamming it. Remove foreign object. If it does not vibrate then you may have a bad motor or main board. To test if you know electronics look at board and find connection for motor and check if you get 120V if so then either bad motor or stuck. Good Luck

C2 error may indicate a pump problem or too slow pump action this may be due to a blockage in the pump or a failed or failing pump capacitor this is not an expensive fix look for a replacement capacitor on Maplins of uk white goods web site you can get the size from the details on printed on the capacitor.

Most likely a blockage in the spray arm / nozzles or the draw is not fully sealing the water inlet allowing the water to bypass the spray arm /nozzles and go directly into the machine.

Fault in heating phase. Could be: Heating element, wiring between heating element and power board, power board (usually relay). Sometimes can help to resoldering (cold solder joint) or replaced relay on power board. Dado

http://www.electrolux-ui.com/

There are several reasons if spray arms doesn't spray water. First you need to check efficiency of circulation pump. If it works, then should check the turbine of circulation pump. Sometimes turbine blades can be broken and the pump does not produce enough pressure to turn the spray arms. Be sure to check that the filter is not clogged which can also causes same problem. Finally, check that the nozzles of spray arms are not clogged. So, could be: - motor circulation pump - circulation pump - filter - spray arms - electronic or power board Dado

1. To remove upper basket spray arm, tilt it down hard. 2. Clean spray arms jets. 3. Place cleaned upper basket spray arm back in position against the connecting piece: press the two together firmly, until you feel them snap into place. Dado

Customer always needs to follow the manufacturer's instructions about cleaning and maintaining the appliance. If there are some ambiguities then you should contact an authorized service center. I personally believe that it is not a good idea to clean hob with steam cleaner. 6.3 Cleaning the hob • Remove immediately: melted plastic, plastic foil, and food with sugar. If not, the dirt can cause damage to the hob. • Remove when the hob is sufficiently cool: limescale rings, water rings, fat stains, shiny metallic discoloration. Clean the hob with a moist cloth and some detergent. After cleaning, rub the hob dry with a soft cloth. • To clean the enamelled parts, cap and crown, wash them with warm soapy water and dry them carefully before you put them back. Dado

Error code E49, generally speaking, at AEG dishwasher does not exist. Dado

AEG produced a lot of model dishwashers over several decades. Please, specify AEG model or product number. Dado

You must specify more symptoms than we can help you. It's just like going to the doctor and ask him why I'm sick. He needs more symptoms if you want to help you. Dado

The most common cause of a fault "i10" is closed valve on the water supply line. So this failure indicates a problem with filling of water. Possible error causes: Closed water tap, Inlet valve faulty, inlet hose bent, softener system clogged, pressure switch or pressure switch hose obstructed or leaking, wiring from pressure switch to printed circuit board (PCB), wiring from inlet valve to PCB and finally PCB. Dado

The problem when the dishwasher does not heat is failure which requires to remove the qualified personnel and therefore error code is not shown on the display but it is visible in the service mode. Possible error causes: faulty heating element wiring between heating element and PCB PCB (printed circuit board) Dado

It is possible, but definitely before check if something is obstructed or blocked the drain pump. Error "i20" means there is a problem with draining water. Dado

The most common cause of a fault "i10" is closed valve on the water supply line. So this failure indicates a problem with filling of water. Possible error causes: Closed water tap, Inlet valve faulty, inlet hose bent, softener system clogged, pressure switch or pressure switch hose obstructed or leaking, wiring from pressure switch to printed circuit board (PCB), wiring from inlet valve to PCB and finally PCB. Dado