20 Most Recent
Akai LCT2060 Television - Page 3 Questions & Answers
No lights
Best to replaced same power supply board.Because of voltage and amps in the boad,will burn ur other boards,not same in and out put AC/DC out for other boards.
Completely dead
Power supply board is dead. Tries Shopjimmy.com,Ebay.com to buy a refurbish power supply board for the replacement.
I need the code for the lct2060 lcd tv.
I recently bought a used LCT2060 that had no remote. I figured my
comcast cable remote would work without a problem but it didn't. So 3
universal remotes later I found my solution...a
radio shack
universal gamer remote. It controls up to 5 components plus your
xbox360, playstation and pc. The price on sale was a mere 12.97, not bad
if you ask me. Hope this helped. The code that worked for the
Akai
was 11676. Take care...
Remote do not work
I recently bought a used LCT2060 that had no remote. I figured my comcast remote would work without a problem but it didn't. So 3 universal remotes later I found my solution...a radio shack universal gamer remote. It controls up to 5 components plus your xbox360, playstation and pc. The price on sale was a mere 12.97, not bad if you ask me. Hope this helped. The code that worked for the Akai was 11676. Take care...
I am using the tv as a computer monitor and I was
Hi Dbroker
If you are using a lcd tv with the 16:9 format as monitor then the 1280X768 is the best resolution to use.
But if your monitor/tv cannot accept this resolution then 1024X768 would be the optimal.
Hope this helps Goodbye
I have an Akai lct
Hi
Thanks for using FixYa. From what
you have described it seems the issue is with the power board or the main board
we’ll need to check few things. When you open the unit up; take a look at the
power board-the board where, the power cords/plugs goes into. You might see
some filter capacitors a little bulged up in the top-If this is the case-this
is your defective part(you can try to replace them-but some soldering equipment
is needed). If not, then probably the main board has gone bad. This is the other
board-where all he inputs are going into. Also check for the Backlight Inverter
Board if the sound is coming fine from the TV however as its shutting off so it
should be either the power board or the main board. All this is only
recommended if you have electrical expertise and know how to solder/re-solder
components. . Please do accept the solution if
the issue is resolved or else revert for further assistance.
Thanks
Rylee
It wont turn on...........
It seems that your unit has some sort of PSU fault, or a problem that is shutting down the Power Supply Unit, PSU. This happens so that no further damage, and possible fire will occur.
You need to take the unit to a reputable service centre/man and ask for a firm "Quote" for the work to be done.
NO SOUND
If the tv is not set on mute, then you could possibly have a blown audio ouput. Usually caused by overheated and burnt out capacitor near the audio outputs. An ohmmeter can be used on the bottom of the board where the soder joints and then you can test the capacitors. Most are usually around 25-30 ohms.
A difuser and soldering iron will be needed to remove last little bit of stored power in the capacitor. Then solder it off.
Then you can go to tigerdirect.com and purchase a new one.
Or about $250 for replacement by shop.
Does not come on
Recheck ALL connections-correctly,IF problem persits, UNPLUG TV.allowing it to ReSet Itself.Hopes this helps.BrtRal
LCT2060 has sound but no picture.
connect your allconnectrion to television again.
Also check your power supply and earhing proper working.
Reset all settings to factory defaults.
Not finding what you are looking for?