20 Most Recent
Magic Chef CER3725AA Electric Kitchen Range - Page 2 Questions & Answers
Magic Chef Oven 3888VRA beeps and shows F-1.
Hi this is indicating a Defective touch pad or clock (ERC).
This simple test will help determine whether the ERC (Electronic Range Control board or Clock) or the touch pad is defective when F1 error code is present. Follow carefully, and with caution.
Note: Some models incorporate the touch pad in to the ERC as a single assembly, in which case this test is not necessary. Simply replace the ERC (Clock).
Warning: Do not preform this test if you feel as if you are not qualified to do so. Contact your local service depot, if needed.
1. Disconnect power to the range (unplug the range power cord or turn the power off to the range at the circuit breaker). It is very important that the power to the range has been disconnected, so please double check before continuing.
2. Gain access inside the control panel.
3. Disconnect the touch pad (also called keypad or membrane switch) ribbon from the ERC.
4. Make sure there are no lose wires, or anything else that may cause a short when power is turned back on. Assemble the control panel back the way it was.
5. Turn the power back on.
6. Wait for at least one hour to see if the F1 code comes back (usually accompanied by a beeping sound).
7. If F1 comes back, replace the ERC. If it does not, replace the touch pad.
11/17/2009 11:50:24 PM •
Magic Chef...
•
Answered
on Nov 17, 2009
Have a magic chef oven, f1 display after self cleaning
F-1 is a fault code.
Disconnect the power plug or turn range power off at circuit breaker. Wait a couple of minutes, then plug the range in or flip the range circuit breaker to ON.
Oven control beeps & displays any F code error (for example
F11) - Electronic control has detected a fault condition. Press
CLEAR/OFF to clear the display & stop beeping. Reprogram
oven. If fault recurs, record fault number. Press CLEAR/OFF &
contact an authorized service agent.
Cant open oven door!
Unplug The Stove From The Power Source For A Minute Then Plug It Back In. Then Check it Again
MY OVEN WILL NOT GET
are you sure it's only reaching 220 degrees Farenheit? Many stoves can be set to display either in Farenheit or Celsius. You didn't post a model # but if you look in your use and care guide you can change it back to Farenheit scale Hope this helps
What is this F-! mean
F-1 is a fault code.
Disconnect the power plug or turn range power off at circuit breaker. Wait a couple of minutes, then plug the range in or flip the range circuit breaker to ON.
Oven control beeps & displays any F code error (for example F11) - Electronic control has detected a fault condition. Press CLEAR/OFF to clear the display & stop beeping. Reprogram oven. If fault recurs, record fault number. Press CLEAR/OFF & contact an authorized service agent.
Preheat beep indicator is inaccurate
It's working ok. These often beep after a preset time. It may be set to beep at 10 minutes. Not always at the temp set. It is usually close enough though.
Magic chef stove
If the oven is working but the control does not light up then you will have to replace the control. If the oven doesn't work then will have to check and see if you have power to the control. If power is there then the control is bad.
10/25/2007 10:42:47 PM •
Magic Chef...
•
Answered
on Oct 25, 2007
Magic chef electric range model 38HK-6TXW
MAGIC CHEF Range/Stove/Oven Fault Codes
Failure
Code
Condition
Check/Repair
F1
1. Watchdog on board
2. Touch membrane defective
To determine which component is at fault, disconnect ribbon strip. If NO fault code, replace membrane, otherwise replace board
F2
Oven too hot
Check oven temperature sensor
F3 F4
Open or shorted oven temperature sensor
Replace
F5
Hardware and watchdog circuits disagree
Replace clock assembly (also called the ERC)
F6
Missing AC signal
Replace clock assembly (also called the ERC)
F7
Function key shorted
Replace touch pad
F8
Analog/Digital converter
Replace clock assembly (also called the ERC)
F9
Door latch
Check door lock circuit
F10
Function key stuck
Replace touch pad F6 means no ac signal and will need to replace the oven control.
10/19/2007 12:49:00 PM •
Magic Chef...
•
Answered
on Oct 19, 2007
Not finding what you are looking for?