20 Most Recent EuroTech EWF150 Front Load Washer - Page 2 Questions & Answers

As you said in the question you are using Euro Tech EWF 150 you are washing machine have problem with the belt.Belt will be damaged you just need to contact the nearest washing machine center so that you are washing machine will be just fine.There is no big problem it's just a small problem.If you no how to fix that belt means you can fix the problem.Thanks for your question.

Hi from retired Englishman in SW France,
Spares Suppliers
You will need to type into your search engine/web browser '(make model number) washer spares' and you should be presented with a number of sources from which you can order. Alternately you could try telephone directories for spares suppliers but I would think the former would be more successful.
If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C.

Hi from retired Englishman in SW France,

You will need to type into your search engine/web browser '(make model number) washer manual' and you should be presented with a number of sources from which you can either download for free or have to pay a nominal amount.
You could also try the manufacturer's web site direct ;-0)
If you are after a service manual you may find that the manufacturer provides only to its service engineers ;-0(

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C.

Hi

The issue is with the door lock assembly that is bad and should be replaced. If the door lock assembly is bad the control will sense that the door is open and so will not start a spin cycle. If you want you can test the door lock assembly with a voltmeter before replacing it. Hope this helps...please post back for further assistance.

Daniel

check your wiring to the door lock assemby as well as check the water valve in the rear first assuring that you have water to the valve then assurinig that water does go past the valve. one questions though what made you replace the motor control board and the wiring harness did you have the appropriate error code please message me back with your finds as well as any further questions you may have Thanks again Rick

You have to replace the whole door seal.It can be done through the port hole,difficult but achievable or you can strip the front of the appliance off and do the inner part easier.

Unplug the appliance.

Open the door and take the seal retaining ring out of the door seal.

Peel the door seal off the front panel and fold it inside.

Take the seal retaining ring/spring out of the tub side of the seal.

Pull the seal off and take it out of the appliance.

Fit the new seal to the tub,look at the seal and tub for matching arrow marks to help align it.

Fit the retaining ring/spring into the groove in the seal and over the lip of the tub.

Fit the seal to the front panel and then fit the retaining ring into the seal.

Restore the power to the appliance and leak test it.

If you find you can't get the seal on.

Take the top off the appliance.

Take the dispenser out.

Take out the screws revealed.

Take out the screws holding the door lock.

Take off the plastic cover below the door and remove the screws revealed.

Take the front panel off.

If the panel won't come down and off there will be a hidden screw that requires the facia panel to be removed.It's snap together plastic,just release the catches and carefully remove the facia.

Take the screw out, take the panel off.

Fit the inner part of the seal to the tub.

Reassemble the front of the appliance.

Fit the seal to the front.

Leak test the appliance.

Your water pump is clogged with debris.

Tilt washer back to access.

if you can pull the lid up or a panel off the bottom to expuse the back side of the lock there should be some sort of plastic cord comming from it. that is a manuel unlock---pull on it hard. im sure you have tried unplugging it so it could try to reset its self

Overloading, see if ur spin cycle wok ok by doing a empty load and watching it

if your gettig hot water on rinse.your fill hoses are not correct.rinse is only cold.switch the hoses.if that dosent solve the problem call for warrenty

If your dishwasher's cycle times are too long, check these:

Water pre-heating
Cycle not completing
Water pre-heating
Your dishwasher may pre-heat the water. If so, and if the water entering the dishwasher is
cool, the heater may take up to half an hour to heat the water.

To avoid the wait, increase the incoming water temperature before turning on the dishwasher.
Do that by running the kitchen sink faucet until the water runs hot. Or increase the temperature
of the hot water to the entire house at the hot water heater.

Warning! To lessen the risk of scalding, don't set the hot water heater temperature higher than
120 degrees Fahrenheit.

see if the the plastic shipping cones have been removed from the bottom.

Motor coupler could be bad.

ask your local retailer , we do not have that make here

hi Tzamora803. this is all i could find,and its from another fixya member called,d floyd,so its the person you need to thank if you ever come across him. Front Load Washing Machine not draining and or not spinning If you are having problems with either not draining or spinning, with your front load washing machine, then you need to realize that they can be interrelated. Mostly in that if your washer is not draining the water it will not spin at all or at least not properly. There also can be others problems that will stop or slow down the spin, but the water not draining is the most common one. So, if you are stuck with a washer that is full of dirty stinky water then here are some things to start checking. First get that shop vac out or a bunch of rags and a bucket. The water needs to go. The shop vac will pull the water out the drain hose. Just remove it from the standpipe and place the nozzle in the hose and pull the water through the pump and into the shop vac. Of course if you cannot pull the water out this way, you already know that the pump is blocked or clogged, then just vac out all the water you can from the inside of the washer. If all else fails, remove the front cover and take off the hose going from the tub to the pump. Yeah, water will go all over, but that is what the rags and bucket are for. When the water is gone, you can then pull all the stuff out of the hose and pump, that are causing the problems. Most of these pumps are very easy to take apart and clean out. This will make sure that there isn't anything inside the pump that can stop it. They are not very strong motors and something like a toothpick may stop it. Now, where this get tricky is that there are sensors that check the water level and adjust the spin. If your water is not draining, your washer will not spin either. For many washing machine problems that are drain and spin related, this simple cleaning will solve your problem. But there are other possibilities. The lid switch is the old problem that keeps raising it's ugly head on all washers. Bottom line here is that if the washer thinks that the door is open, the things don't work right. Check out the door switch to make sure it is operating properly. Make sure the new front load washers are on a good solid level surface. If the machine can move around then the sensors will often sense the movement and not allow the machine to reach full spin speed. Some manufactured bases may not be stable enough to give correct readings to the machine. If your washer is moving around, then fix that problem. The timer can also be a problem. Many will wear out and then get to a point in the cycle, then not advance any further. Also the computer controlled sequencers can also get glitches and may need to be reset. You can check out the timer by manually advancing it, and the computer reset procedure will be in your manual that you received with your washing machine. By going through this check list you can check out the problems that most handy persons can handle in the home. To make sure you have a the best chance at a trouble free washing machine, make sure that you do not leave anything et into your washer that will cause it harm or plug it up. http://www.fixya.com/support/r4312694-washing_machine_maintenance http://www.fixya.com/support/r3880845-washing_machine_problems_no_water http://www.fixya.com/support/r3907570-buy_appliance_parts_online http://www.fixya.com/support/r3880533-washing_machine_fix_washing_machine_no http://www.fixya.com/support/r3867591-washer_troubleshooting_water_not http://www.fixya.com/support/r3864434-washing_machine_door_jammed http://www.fixya.com/support/r3663122-washer_problems_washer_noise_when http://www.fixya.com/support/r4356970-clean_washer