20 Most Recent
Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher - Page 6 Questions & Answers
Bottom drawer locked (stuck) open
fisher and paykel sent me a solution - turn off at wall and unplug then turn back on. The dishwasher reset itself and the drawer unlocked.
The Fisher Peykel dual drawer
can you see a small lock inside the display panel??? the control may be locked. another issue might be a broken heater plate, not a very home owner freindly part to change( heater plate has a fuse inline that would kill power to function
Water in drawer
have you tried removing the trap and cleaning it? Look at the cavity to make sure no labels have clogged the area and wash the trap to remove all oil/grease and run on a delicate cycle.
11/26/2013 10:30:43 PM •
Fisher and...
•
Answered
on Nov 26, 2013
Fisher and Paykel Dishwasher beeps while it washes dishes. Any solution?
Here is a suggestion: I had problems with the top drawer on a model 603I, I found that the control board under the drawer cover (at the upper right corner) had a broken latch. This allowed the control board assembly to drop down at the right side which caused the electronic eyes at the side of the drawer to become misaligned. This was giving false information to the control board indicating that the drawer wasn't closed properly. My problem was fixed by securing the control board back in place making sure the electronic eyes were lined up properly. (Note: The electronic eyes I am referring to include two clear plastic tubes about an inch and a half long to the right of the control board. These tubes must be properly lined up with the led and photocell on the side of the control board) It sounds complicated but if you take the drawer cover off you will notice the control board alignment immediately. Its an easy fix if this is your problem. One way to fix it is to take a piece of string and tie the board back in place. (That's what I fixed mine with and it has worked like new ever since.) NOTE: MAKE SURE THE POWER IS TURNED OFF BEFORE YOU BEGIN THIS REPAIR!
My control panel in the top dishwasher is not
Here is a suggestion: First turn the breaker for the dishwasher off for a minute or so then turn it back on. This will reset the controls. After that you should be able to select the cycle you want. Now for information on top drawer acting crazy. I had problems with the top drawer on a model 603I, I found that the control board under the drawer cover (at the upper right corner) had a broken latch. This allowed the control board assembly to drop down at the right side which caused the electronic eyes at the side of the drawer to become misaligned. This was giving false information to the control board indicating that the drawer wasn't closed properly. My problem was fixed by securing the control board back in place making sure the electronic eyes were lined up properly. (Note: The electronic eyes I am referring to include two clear plastic tubes about an inch and a half long to the right of the control board. These tubes must be properly lined up with the led and photocell on the side of the control board) It sounds complicated but if you take the drawer cover off you will notice the control board alignment immediately. Its an easy fix if this is your problem. One way to fix it is to take a piece of string and tie the board back in place. (That's what I fixed mine with and it has worked like new ever since.) NOTE: MAKE SURE THE POWER IS TURNED OFF BEFORE YOU BEGIN THIS REPAIR!
The top drawer turns only on rinse mode, can't select any other option
First turn the breaker for the dishwasher off for a minute or so then turn it back on. This will reset the controls. After that you should be able to select the cycle you want. Now for information on top drawer acting crazy. I had problems with the top drawer on a model 603I, I found that the control board under the drawer cover (at the upper right corner) had a broken latch. This allowed the control board assembly to drop down at the right side which caused the electronic eyes at the side of the drawer to become misaligned. This was giving false information to the control board indicating that the drawer wasn't closed properly. My problem was fixed by securing the control board back in place making sure the electronic eyes were lined up properly. (Note: The electronic eyes I am referring to include two clear plastic tubes about an inch and a half long to the right of the control board. These tubes must be properly lined up with the led and photocell on the side of the control board) It sounds complicated but if you take the drawer cover off you will notice the control board alignment immediately. Its an easy fix if this is your problem. One way to fix it is to take a piece of string and tie the board back in place. (That's what I fixed mine with and it has worked like new ever since.) NOTE: MAKE SURE THE POWER IS TURNED OFF BEFORE YOU BEGIN THIS REPAIR!
Dishdrawer: Does not start, just beeps once
Some sensors on the unit are telling the controller there is a fault.
Most likely the sensor checking the drawer is open or close is giving a fault. It is likely the drawer has come off the rail.
Loose sealing tray in to drawer keeps drawer from sliding
You might be correct in your assessment. The top drawer door seal has come undone. It is a very labour intensive process to put it back. Could also mean the actuators that operate the seal are undone.
To get to the actuators and seal you will have to get the drawer out from its housing and then give it a shot. If you are confident of getting to the next step then post a comment. Otherwise a qualified technician is your best bet.
Not finding what you are looking for?