20 Most Recent Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher - Page 4 Questions & Answers

Yes this means that the machine is detecting water under the bottom drawer. Pull the bottom drawer out and soak up the water with a towel and then the error will go away. This happens often because something gets put in the drawer that's too tall and doesn't allow the lid to come down all the way and seal.

you will find this diagnostic service document useful. http://applianceassistant.com/ServiceManuals/dishwasher-fisher-paykel-dish-drawer-dd603-ds603-service.pdf#zoom=100#scrollbar=1 The likely reason for top drawer not starting wash program when you press start button is the drawer home sensor is either faulty or the drawer is misaligned. This means controller thinks the drawer is open and does not start the cycle.

Is the filter in the hose where it screws onto the tap clean?, if this is okay then most likely the valve.

9.9.1 Remove the drawer front 9.9.2 With the tub opened release the tub clips and push back the drawer rails. 9.9.3 Carefully release the four wiring cover clips from the front lower section of the tub taking care not to damage them. 9.9.4 Release the three clips on the underside of the tub which retain the wiring cover. 9.9.5 Pull the tub fully open and lift it up at the front (this makes it easier to remove the wiring cover from the rear of the tub). 9.9.6 The wiring cover may now be carefully moved forward to release it from the rear of the tub. controller. . 9.10.6 Unclip the drain hose cuff from the motor assembly taking care not to misplace the non-return flap valve so you know where it sits. Replace flap valve and refit in reverse order. Not sure why you need to take the top drawer out if you have already got the bottom drawer out and only need to replace the valve in bottom drawer.

Turn power on wall off and pull the cable out. Get the bottom drawer out from the housing and carefully rest it on soft padding like a cushion on the floor. Take towels and dry the base of the main housing. Take a hair dryer to do the rest. Put things back in. Sometimes foaming due to too much detergent can also trip flood switch.

Replacing lid seals on the dishdrawer is not for the faint hearted. In particular if you are replacing the lid actuator and motors that go with it. http://www.genuineapplianceparts.net/ecart/item.php?item_id=386&category_id=58

The pump and motor for DD603 is the same device. It is a rotor lodged inside a cavity under the drain filter plate. I am assuming the dishdrawer is drained properly and at end of the wash there is no water sitting inside. You need to take the rotor device out from its cavity and check for damage. This video will help.http://www.youtube.com/watch?v=UXzuJvKIIgU

Not sure whether there is any easy way to repair these. However, it is unlikely these are sold separately. Will need to buy the whole kit. http://spares.bigwarehouse.com.au/product_info.php?cPath=64658_64876_68136&products_id=1617540

Most likely the lid seal is dislodged and is obstructing the bottom drawer. Need to manually operate the lid seal actuator yoke and motor to bring the seal back to normal position. Can be messy. Will need to get the bottom drawer out from housing and work on lid seal assembly located in the main housing. http://spares.bigwarehouse.com.au/images/files/6145_5635c632f6805f5644d3f35b6feea5bc.pdf

The display panel has come off the housing. May need to be replaced or refit. Remove front panel to check. Turn mains power off and pull out the plastic clamps from the side with plyer. Careful not to drop any parts on the front panel module. Avoid jerks or too much force.

If you can operate the dishwasher but the display is blank then it is likely the LCD panel is faulty. Needs to be replaced. see below. http://spares.bigwarehouse.com.au/product_info.php?cPath=64658_64876_68136&products_id=1653549

If this is part of warranty repair then the technician should be asked to come back and fix. Try to turn off mains power and then use a clean damp cloth and run on the program selection panel on top of drawer lid. But most likely some dirt on the underside of the panel. Need to take controller out and clean it.

what model fridge do you have. This fault is posted in the dishwasher section.

The motor in the front is the dryer motor. This will keep running until the dry cycle is complete. If it is beeping and there is no other display or light flashing then this motor is faulty and needs replacement.

Check to see if the Child lock is on...Check your email