20 Most Recent
Fisher and Paykel IWL12 Top Load Washer - Page 6 Questions & Answers
My F and P Eco Smart top loader gets to the rinse
You need to unplug that machine and not use it again until you figure out the issue. I would say it sounds almost 100% like you have a bad water pump. If the pump is getting wet or has a short in the coil, it will get hot and shut down. Bail out any water that is in the tub currently, and inspect that pump ASAP. if you continue to use it like this, you risk burning out the motor controller.
Fisher Paykel Washer IWL 12 error codes 130 & 240
Had the same problem cleaned the terminals worked for a bit and came back. The problem is that the little circit board that the plug goes onto that sits between the winding of the motor the copper tracks are so small and they corrode. If you are handly with a solding iron you can replace the tracks with small wire, its mainly on one leg of each of the transistors that are all parrelled up. You can tell because it goes black. Or the easy way just take off the motor unpluging the sense plug then the three main power connectors Yellow, blue and red making sure you mark the correct order to put them back on. The sensor board just pulls out of the windings with a little arrow to but it back in the right place and buy the small board it has the part number on it to find it on the web. I only has three bits on it can't be expensive. Soldered mine up works a treat make sur you clean up the plug aswell, it mainly played up in humid weather.
I have model number GWL11US.
Sounds like your off balance switch might be faulty.
Located under console at the back right corner
Also called a oob switch
Error code 37 for iw811
Code 37 is 1:pump blockage
2:your diverter valve is blocked as well
3:check to make sure your drainage hose is not kinked
Machine will fill with water,will not spin to wash
Hi just read your posting.Now when the machine beeps an error code will appear.This will be in your LCD display or in a series of lights being lit.Now the lights that are lit when the machine is beeping will be in a row of 8 lights.Starting from the left to right which lights are lit when the machine stops and beeps,Is it the 2nd and 5th or the 3rd and 7th ---etc---? Please reply reply with additional information and I am sure I can help you rectify this fault.Looking forward to your reply.
Fisher and paykal IWL16 washing machine showing
Hi just read your posting.Error code 37 means PUMP BLOCK ERROR.Drain some of the water by hand enough to look under the machine to the front right.Do you see a fan.If you do this is your pump.If you do not see a fan then you have the new style of pump.Please reply on which style of pump you have and I will guide you in rectifying this fault.Looking forward to your reply.
Hi, my washing machine is emptying the water as it
Hi Kala just read your posting.Is your machine draining into the laundry sink or some place else?If it is draining into the sink then the problem with your machine is the divert er valve.The diverter valve is in the drain out position when it should be in the recirculate position.There are 2 reasons that the valve is in this position,The 1sr the diverter is faulty or the 2nd the control module is faulty.Please reply on how you would like to proceed and I will help you as much as I can.Looking forward to your reply.
Our wash machine will not run on fast spin. It
Hi just read your posting.I have seen this problem many times before and the problem is all or some of your suspension rods are faulty.They will need replacing.They are not that expensive and if you purchase a set of them I will guide you step by step in the replacement of the rods.The problem on the rods is the rubber plungers wear and the rod reacts like a faulty car shock absorber.I am nearly 100% sure on my diagnosis but the only way to be sure is to look at the machine.Although this problem is nearly always caused by faulty suspension rods, sometimes when there is water loss in the balance ring on the bowl this has the same symptoms.Lift the lid and rock the bowl from side to side and you should hear water up top of the bowl which is your balance ring.Please reply on how you would like to proceed and I will help you as much as I can.Looking forward to your reply.
Fault 37. Machine will not empty bowl
Hi just read your posting.Now error code 37 is called PUMP BLOCK ERROR Do you hear the pump pumping any water if you advance the cycle to spin and push the start button?Please reply with additional information and I am sure I can help you.Looking forward to your reply.
My washing machine keeps coming
Hi just read your posting.Now error code 130 is called SINGLE ROTOR POSITION SENSOR ERROR.This means the rotor sensor which is attached to the motor is faulty or the wiring to it is faulty or the control module is faulty.Unfortunately to test the rotor sensor you need an RPS TESTER.I can help you test the wiring to the rotor sensor but unless you have an RPS tester I can not help you test the rotor sensor.Please reply and let me know how you would like to proceed and I will help you as much as I can.Looking forward to your reply.
Fault code 37
fault code 37. washing machine will not empty bowl.
We suspect Fisher Paykel IWL12 washer suspension
Hi just read your posting.Is your machine going out of balance a lot? Sorry to ask you this but why do you think the suspension rods need replacing?Please reply with additional information as there is a way to rejuvenate your old rods.Looking forward to your reply.
The machine was about to start the spin cycle when
Hi just read your posting.Now when the machine beeps a series of lights will light up.They will be in a row of 8 lights.Starting from the left to right which lights are lit when the machine is beeping.Is it the 2nd and 4th or the 1st and 7th ---etc---?Please reply with additional information and I am sure I can help you.Looking forward to your reply.
Not finding what you are looking for?