20 Most Recent
Vizio L37 Television - Page 8 Questions & Answers
Why does my channel scan stop at 30%
A few months
It is important to know the number of channels on your cable or TV input.So if these signals are good- VERY IMPORTANT TO HAVE STRONG NOISE FREE SIGNALS- then it should be scanned. If this is cable the chances are that the signals are bad or has some noise . It will be best to confirm with your operator before we can suspect the TV section or the IF processor.
10/18/2011 5:18:44 PM •
Vizio L37...
•
Answered
on Oct 18, 2011
Recently(within the past 6 months...) have been
Hi.
A digital TV handles the color in three channels, red green and blue. Your TV has a problem on the red channel. That causes pictures getting yellowish. The computer functions can compensate the fault, but that is not a solution. If the problem happens on every input and also with internal tuner, then the logic circuits that elaborate video signal are defective. The main board is usually replaced to fix the problem. Before replacing the main digital board the technician can check if any repairable fault is found. A contact in one of the input for example may short the circuit affecting one of the color channels. In that case the tech will only need to resolder the connector on board to fix the problem. More commonly the whole board must be replaced.
Here parts for this TV:
L37 TV Parts ' ShopJimmyRegards.
Ginko
9/19/2011 10:33:52 AM •
Vizio L37...
•
Answered
on Sep 19, 2011
My vizio 37 inches hdtv went black with no sound.
Yes,power of the tv just have a tv LED power light indication flashing or blinking only?Yes.Tries tv unplug,replug it back like about an hour later for the tv to do a whole resetting itself back to factory setting.Tv should be working again.If not than the tv power supply board have a problems and the causes.That the board where the tv power a/c cord plug into it.Tries websites like Shopjimmy.com,Ebay.com to buy a whole new refurbish a tv power supply board for the replacement.
9/6/2011 3:12:54 AM •
Vizio L37...
•
Answered
on Sep 06, 2011
My vizio l37 hdtv went black it is getting power
You need to replace the main board (signal). It is the board with all the A/V hookups on it. The part number is a number with 3 sets of 4 numbers and at the end of this number there is a number letter sequence with ( ) parentheses around it. Do a search on ebay and you should find one. Be sure to match the numbers I mentioned to the one on ebay!
8/23/2011 2:22:42 AM •
Vizio L37...
•
Answered
on Aug 23, 2011
I have a three year
Take off tv back and observe power supply board and back light inverter board for burn spots, replace that board that has burn spots.
Power supply board is where AC cord goes in and inverter board would be installed at side of lcd panel. Required board would be available in
discount-merchant.comThanks.
8/16/2011 11:11:27 PM •
Vizio L37...
•
Answered
on Aug 16, 2011
No picture, but sound on
I'm sorry that the TV is not displaying any picture on the screen. Please follow the troubleshooting steps and check the operation:
- Please make sure that the connections are secure and proper.
- Try connecting a different video source like DVD player or VCR and check the operation. If it works with another device, the issue might be with the input device that you're using now.
- Also try connecting the device to a different port on the TV if no other devices are available.
- If the issue persists, try with a different cable.
- Perform a power resetting and check the operation. To perform the power resetting, unplug the TV from wall outlet for more than 5 minutes and then reconnect it.
If the issue persists, after all above troubleshooting steps, service may be required. You can click hear to setup a service for the TV.
Also it would be good if you can come back with the model # of the TV to check whether the issue can be resolved with a firmware update.
Thanks for understanding. Please let me know if you require any clarifications/additional help.
8/10/2011 2:50:59 PM •
Vizio L37...
•
Answered
on Aug 10, 2011
I have an L37HDTV10A that i just replaced the main
Go into ur tv Menu goto OPTION go down to Output Select,press enter make sure selection on (Fixed).This fixed selection will pick for the tv out put to tv speaker.Tv should have sound now on it speakers.Try website like Remotes.com to buy the tv original remote work for the best used for to reajustment setting and setting on the tv Menu.
7/29/2011 9:00:14 PM •
Vizio L37...
•
Answered
on Jul 29, 2011
I need remote codes for
Remote codes for set top boxes (aka cable/satellite boxes) are the responsibility of the service provider to generate. You have to call Dish network and ask them for a code, dont let them xfer you to Vizio THEY WILL NOT BE ABLE TO HELP.
7/18/2011 2:27:51 AM •
Vizio L37...
•
Answered
on Jul 18, 2011
Not finding what you are looking for?