Top 20 Viper RCVGC022 Remote Control Questions & Answers

It sounds like there's no power going to the starter wire. Try and locate the brain under the dash for the remote start. It should be black and about twice the size of a deck of cards with a few harnesses hanging out of it. Usually it is zip-tied to a wire harness or bracket to keep it secure and from falling down onto your feet. There should be several wires much larger than the others, and you should see fuseholders on the 2 red ones. Usually one of the fuses is used solely for the starter. Check both fuses on these larger wires. Should be 30 amp green ones if I remember right. Also, while you have the brain accessible, write down the model number on the brain itself to help you in the future. Most DEI remotes can be used for almost any DEI/Viper/Your Valet system, so it's really hard to tell what you have just by looking at the remote. If the fuses are fine, you may need to take it to a shop (anyone that sells Viper and such). If you have a chip in your ignition key, it may also be the security bypass module that gets installed with the remote start. You will only have this bypass module if you have the little chip in your ignition key. Hope this helps, good luck.

Chad

check first your remote control if it is sending a command once you press a button, use the camera of your cellphone to check whether the infra red light is emitting a signal once a button is press .to do it

open the camera and aim it on the remote sensor press a button and you should see the sensor is lit.if not then you need to open the cover of your remote and try to resolder the terminal of the sensor.try to clean also the remote reciever of the viper..let me know if this work...or post a comment if you need further assistance.

the fact that you have to get closer sounds like the batteries are getting low

Greetings Microluv,

Simple question, have you changed the battery in your remote lately? I was having similiar issues with my remote start and it was a simple matter of changing the batteries in the remote.

I figured lets eliminate the easy stuff first. :)

Dorothy
Go Ahead. Use Us.

we have a viper 600hf and it has recently started draining thebattery and it won't stay charged.

u can open the drivers door if u have a 2 key remote just press lock aux lock again pretty fast and u should be great.

First of all did you remove a connection from the battery in your car so that the system can reset?
Try that first and at the same time take the batteries out of the remotes for a minute or so and hook back up.

Change the battery in the keyfob..

Video

https://www.youtube.com/watch?v=X3TWwH-nABk

Viper Support Center - How to turn on the Auxiliary buttons

https://www.viper.com > support > guideTitle=How-to-t... Step 1:Click on the car name located on the top right hand side of the app. Step 2:Click on Vehicle Settings. Step 3:Click on Aux Buttons.

Check the difference in the remote codes.

Please provide more information in regards to your problem.

Refer that question to the manufacturer of the device.

On many of the Viper models, the symptom you are describing is because the remote battery is low. The remote can't be too far from the vehicle. If it is, the system see it as you forgot about the vehicle being remote started, and shuts it back down. A weak battery creates a weak signal and makes the unit 'think' you are far away. The Viper website has instructions on how to disable the whole system, there are many different versions, so find the box and get the model number from it, you will need that to get any further.

vehicle make, model, year?

It has been damaged. Buy an other one. To select a proper universal remote control, you should know about the number of digits to its set-up codes. There are 3 digit, 4 digit, 5 digit, 2 digit and even single digit codes, to some brand devices. After confirming this, check the sites linked here. Both the sites have set-up code list and set-up procedure to many popular brand remote controls. Check which brand remote control has set-up code/s to your device brand, and buy that one according to availability? Brand name of the remote control isn't a matter, but it should have set-up codes in its code list, to the device brand you have. Please note: Every new universal remote control will have set-up code list, and set-up procedure along with its pack. Never accept a remote control, that hasn't both of this. For more details about the set-up codes, visit the site http://electrohelponline.blogspot.com/ Check this site too. http://remotesearch.blogspot.com/ Universal remote controls are available at most of the electronic spare part selling shops. Visit some online sites too, which deals with electronic spare parts.

spray oil into lock

hellllllllo........go to goggle enter model number the video will appear battery # CR-2016...........tkx.......g.scott

I assume you are talking about the sound the body computer generates, I would suggest taking it to the dealer to get it re-programed if that is the problem.

if no spark then you need to check the coil pack it sounds like it may be the problem..

Would like to know this as well. Having the same issue