20 Most Recent Brother SE-270D Computerized Sewing Machine - Page 8 Questions & Answers

If the thread is pulling through the top of the fabric slacken off the top tension to about 4 and tighten the bobbin tension slightly by turning the screw on the bobbin case about a quarter of a turn clockwise and test.

If you are lifting the presser foot and it sorta holds then drops down.....its probably worn and needs replacing. If the machine is well used thats usually the culprit. There is a lob on the presser foot lever that wears and causes it to not stay up. No easy solution other than changing the part.....best left to a pro.

Derek

My advice is to try going to a shop that sells machines and gives lessons for free. I bought from JoAnn's and they gave me lessons on it. I bought a Brother for $549 and I am not sorry because I actually know how to use it thanks to the girls at JoAnn's. I would not be using all of the features if I didn't have the hands on instruction. The manual is great for a refresher but nothing beats doing it and someone answering your questions. Think about it before you buy online, you may save a few bucks but in the long run you will be happy to have a relationship with people who care if you have a problem and can help you.

The solution is to replace the rubber gear that engages with the drive gear. It has melted. Where do I find the part and what is the part number

Usually it is the top threading, tangled thread or a bent needle that causes that problem. You can call Brother at 1-877-276-8437 and maybe they can suggest something else to try.

it's called the feed dog, look in the operation manual to see where it is on your machine & how to adjust it

Go to www.brother-usa.com and download a copy of your manual and read the troubleshooting section.

You could just call Brother customer service, and they may be able to guide you. The phone # 1-877-276-8437. You have a very nice machine so you don't want to have just anyone look at it, be careful who does. My sister learned the hard way. Good luck

You can download your manual, downloads and a help section for free on the Brother website www.brother-usa.com. under the support section. They have a great site and very informative. Hope this answers your question. Good luck

The safety device will activate if the machine has a bind or is unable to run at correct speed. If you turn the handwheel is it tight/hard to turn? if it is than thats it. Now what is binding the machine has to be diagnosed.

Call brother customer service at 1-877-276-8437 or check out the brother-usa.com website for your manual download for free

This is a common problem for these machines with a cartridge type threader. I have tried to find someone to fix one of these and the answer I got from two repairmen was "thread it manually." Apparently the frequency of using the cartridge threading mechanism wasn't tested enough before being put on the market. When it works, it's wonderful but the only solution is to get a second cartridge. When they first came out, I sold them at a place where I worked and they told me to sell a second cartridge with the machine. They said it was so you could have another color handy and ready to go but now when I look back, maybe they realized that using the cartridge daily was too much wear and tear and if the customer had two of these, it would take longer for them to wear out. Just my opinion.

Call Brother customer service at 1-877-276-8437 and explain your problem, they maybe can tell you how to reset.

I think you have a bent needle or it is inserted backwards. Make sure that the flat side of the needle faces the rear of the machine.

Make sure that your thread spool is feeding the thread the right way and when you have it threaded, pull on the thread with the presser foot up to make sure that it is feeding right before you start to sew. Put in a fresh needle and make sure that the flat side of the needle is facing rear of the machine. Refer to your manual, and read it carefully because they have lots of tips. You can also go to www.brother-usa.com and download a manual or call them for free.

when bobbin thread shows on top, it means that there's too much tension on top thread.

1. Check if top thread unwinds and feeds up well. Make sure that the spool doesn't slide off horizontal spool pin. If it falls – it creates too high tread tension by not giving the thread to unwind properly.
2. Check that the needle is good, not sticky, and allows the thread to come through it easily. It should have a large enough eye.

post a comment for further assistance.
Thank you for using fixya have a nice day:-)

What model # is this question about please??


Thanks!!
2

You can order one from Ron at a1sewingmachine.com. Look in your manual to give him the correct terminology.