Hotpoint Ultima WF860 Front Load Washer - Answered Questions & Fixed issues
What does "f08" mean on
The error F08 indicates that the heater relay is stuck.
This could be a fault with either the pressure switch, heater or the module connections.
Think you need to book a service call from engineer.
Hotpoint washer wont work
From the manual page 24:
'Door' is flashing in the display window...
?Shut the door firmly, until it clicks.
The symbol should now go out.
I suspect the door sensor has failed. It thinks you haven't closed the door, so it refuses to do anything at all. It's called a Door Interlock, it has a switch or sensor built into it.
First try unplugging the washer for 60 seconds and plugging back in to try to reset the controller. (Dry hands only!)
If the door interlock is a simple switch, you should be able to check it with an ohmmeter. I would check it first before buying a new one.
The part number is HPTC00085194 or C00085194, here are a couple places you can buy one. You can also find them on ebay.
Washing Machine Door Interlockby Indesit
Door Interlock Washing Machine
WASHING MACHINE DOOR INTERLOCK C00085194 design may vary
How do I set my hotpoint ultima to English language
turn it OFF (seems like the wrong thing to do but do it anyway) then press and hold the 3 middle buttons under the display panel until you hear a beep - they are labelled reduced creases, mini load and time saver. When you switch it on again you get the language menu. There are 4 buttons either side of the display - the right 2 scroll through the languages and the top left one sets it once you've found the English setting. Guten Tag!
Release child lock
You can download the user manual at: http://www.hk-krasnodar.ru/?option=com_k2&view=itemlist&task=user&id=1389 Also you might try holding the child lock down for 10 or more seconds.
Just keeps filling at the start of program and displays H20
Your washer has a bad water valve or fill censor telling machine need more water then to much water sends a flood warning shuts down so will not flood your home look for small clear tube coming from tub to a type control hose may just came off
My washing machine comes up with f..08 fault, what can i do
Apparently that 's a heater relay fault.
No idea where that is on the machine, you could try tracing the wiring back from the heater to where ever the relay is.
Then buy another and connect up exactly as before and see if that fixes it.
How do you fix a fault F06 on a Whirlpool front loader washing machine
The "F06" fault code indicates a drive motor tachometer error. This means the control is unable to properly detect motor speed and the machine will shut down. If the failure occurs during high-speed spin, the door will unlock after 3 minutes. Possible Causes/Procedure: Unplug washer or disconnect the power supply. Check the wire harness connections between the motor and motor control unit and the harness connections between the motor control unit (MCU) and the Central Control Unit (CCU). Based on your symptom and details, the intermittent (F06) error code is likely a loose connection in the harness between the motor and the (MCU) or between the (MCU) and the (CCU). It could also be the tachometer circuit in the motor or an intermittent internal component connection within the (MCU). Since the (CCU) has already been replaced, the failure is likely a loose harness connection or the (MCU). I recommend calling the repair person back out to re-diagnose the failure. by Joey S MARCH 1ST, 2010 ' Be the first to comment
I am getting an F-05 error
Error code F05 indicates that the pressre/waterlevel switch is jammed on full.
Remove lower rear panel of washer.
Remove large black hose fastened to bottom of drum
Remove and clean plastic filter inside hose.
Remove hose onto pump, check for obstruction here, and into the pump.
Please leave feedback.
Thanks.
Not finding what you are looking for?