20 Most Recent Motorola Mobility V265 - Page 2 Questions & Answers

it not working i did MIN ang MDN

Is It A Motorola Licensed Battery?

It Might Be That It Doesnt Work Properly With Your Phone.

Good Luck :)

Regards,
Sophie.

On the back of the phone is a small button this is the battery cover release button, depress and slide back and lift off

TAKE IT TO CINGULAR ARE THE COMPANY U GOT IT FROM

Have You Got Water In There?

If You Might Have,Take It Apart And Leave It All To Dry Somewhere Warm.

Good Luck :)

Regards,
Sophie.

Dear. most chances are that that the flate of ur phone is bad connect be cause of dropping. just open it and reattach the cable will ok. cable is from board to lcd and it may be bad connect on any side lcd or board first check it from board side if no t ok then from lcd side even no ok change a new cable.

Try powering your phone off ... Taking out the battery ... wait about 5 seconds then put the battery back in and powering the phone on and trying the cam again.

If it works now, it was a software lockup/glitch ... If it still doesn't work then your phone needs replacement.


Tanya

1 of two things: Go into your settings and look for either "Keypad" or "Display" and see if keypad lights are set to ON.

2. Your phone does have a light sensor built into the keypad, normally the keypad will not illuminate unless insufficient lighting conditions are present. If it's pitch black out and the keypad still isn't illuminating and your settings have the keypad lights ON .... You should bring your phone to the nearest Verizon wireless corporate store to see about either replacement or upgrading.


Tanya

Ok, you could maybe open the phone and look inside of it. But these antennas are just unscrewable, so no need of opening you're phone. check the antenna, is it bended ? crooked ?, broken ? If it is, you can buy other antennas on internet http://www.367net.com/product.asp?Brand=Motorola&model=V265&Type=Antenna and if it is not broken, well the problem could come from the interior of the phone, and well at that point you don't have alot of chances. Verizon said that it can be the internal antenna, but keep in mind that its maybe not true. It probably inside the phone.

This is because the microphone in your phone got disconnected in some way. Probably a faulty contact. This is a known fault for some motorola phones. The solution would be to go to a service center and ask them to check your microphone. It isn't an expensive repair at all. They will be able to do this for you in about half hour or so. It is the safest way to do this, otherwise you will have to dissasemble the phone yourself and check the microphone.

here is the user manual for the v265 check this link; http://www.motorola.com/mdirect/manuals/v265manual_9490A02O.pdf page 21 Hope this helps :)

yeah that is possible. make sure you know what you are doing and don't damage the working LCD screen it might just be easier to replace the whole cuircuit board that the LCD screen is on.

MzRendevous, It sounds like you do have a battery issue. Batteries for cell phone don't tend to last long, but if you do purchase a battery, try this to get longer life from the battery. 1. Charge the battery without using the phone until the battery is fully charged. 2. Once fully charged, use the phone like you normally do until the phone shuts itself down because there is no power. 3. Charge the battery again without using the phone until fully charged. 4. Then you can use the phone and charge it anytime you want. You can repeat these steps as much as you want, the more you do it, the more life you'll get from the battery. -- As far as the charger, if you have to adjust it to get it to charge, it could be the cord or the prong on the inside. I'd goto a store and test another charger, if it's available. You can probably get cheap batteries/charges on EBay or anywhere on the internet. Let me know if I was helpful for your questions. John

I expierenced the same problem with my V265 phone. First, note that performing this repair as I did will most likely void any warranties on the phone, and also is an electrical shock hazard. This repair should only be performed if the person/s performing the repair understand these risks and have at least basic technical knowledge in circuits, electricity, and audio. I take NO RESPONSIBILITY for damage or injury in any way, shape, or form. Please to prevent errors or any more damage, read directions fully before starting this repair. - Remove the Battery and make sure no chargers, headsets, etc., are currently plugged into phone. - Remove the housing on the phone which is on the same side of the camera and the external display by gently and carefully prying, making sure not to break the latches or any of the external parts. - Using a Torx bit (I believe it was either a T15 or T20 I used but not sure) or a small flat head screwdriver, remove the 4 screws holding down the board. - Now examine the speaker located at the earpiece of the phone and the two contacts which are on the board you just removed. Look to see if they were properly alligned and if contact is being made between the speaker and the board. (a PINK pencil eraser works great as a cleaner for circuit board contact points) - If contact is being mad and no obvious obstruction is found to prevent contact with the two, the easiest way for me was to take a speaker from another phone, and using it in place of the old one. (If you are willing to use extra time, you could also try finding an actual replacement from a manufacturer.) - I used a speaker from a motorola phone which was actually a few years older than my V265. - After finding a replacement speaker, you'll need to use some trial and error to properly allign it with the contacts on the board and to make it stay in position during everyday use. - For my V265, I had to use a razor and shave away the plastic molding which held the old speaker in place. Then use a VERY small amount of super glue to hold the speaker in position. Then I used a little bit of hot glue to give it some flexible strength. All together, it took me about 1 hour to complete this task and start using my phone again normally. - If any additional assistance is needed, feel free to e-mail at [email protected] leaving your name and prefirably a phone number and best time to call, as a return contact. This will make it easier for me to help the best I can. Thank you and good luck.

[email protected]

This could be due to several reasons such as a faulty battery, a problem with the charger itself, or an issue with the connection between the charger and the battery. Here are some general steps you can take to troubleshoot this issue: Check the Battery: Ensure that the battery you're trying to charge is not faulty. If possible, try charging a different battery with the same charger to see if the problem persists. Check the Charger: Make sure the charger is functioning properly. If you have another charger, try using it to charge the battery. Check the Connection: Ensure that the connections between the charger and the battery are secure and clean. Any dirt or corrosion could interfere with the charging process. Reset the Charger: Unplug the charger, wait a few moments, and then plug it back in. This can sometimes resolve minor technical issues. https://www.manua.ls/stanley/bc15bs/manual If unresolved, you might contact Stanley customer support.

Are you sure you aren't the daughter trying to get around the code? The onus is on your daughter to remember her access code. Your parental code allows you to make restrictions to the phone.The only way to fix it is by doing a Factory Reset. Scrub it clean and start again.https://www.google.com/search?q=hisense+f22+hard+reset..