Magic Chef CGS3760 Gas Kitchen Range - Answered Questions & Fixed issues

Hi,

Here is a tip that I wrote to give details about why your cooktop will not spark to light the burners..Cooktop Range Stove spark ignition does not workheatman101

I'm going to take a wild guess and say that you oven has two heating elements. A lower one for general baking and an upper one for broiling (this means that you don't have a broiler "drawer").

If this is the case, then the problem exists with the pilot/ignition system for the lower heat element.

The systems vary by manufacturer, but the type that I'm familiar with involves and electrical heat element that ignites the gas once it starts glowing. It's possible that a wire has been damaged/disconnected or that the heat element has malfunctioned.

If your oven has a pilot, then it's possible that the pilot went out on the lower element and not the upper. Last option would be an electric "spark" style ignition which may have suffered from the same problems as the electric heat element mentioned above.

Hi, the burners turn counter clockwise. they hold the burner to the top panel. Those need to be removed. Most of the time the tubing is disturb like this, they need replaced as well. Please let me know if this helps or if I can assist you further.

Thanks
Vic

It sounds to me like the spark modual has gone bad. There is a part that is usually behind the control pad and display for the range and oven. It usually looks like a rectangular black box with wires plugged into it. Thats the spark modual. With any luck it will say spark modual on it. Buy the replacement and then plug the wires in the new one just like they were in the old one. You may want to take a photo or write down where each wire goes before you remove the old part. I would also search online for a break down diagram for your appliance so you know for sure how to get to the spark modual. It is a pretty common replacement part so it shouldnt be too expensive. Sorry I couldnt be more specific.

F1 1. Watchdog on board
2. Touch membrane defective To determine which component is at fault, disconnect ribbon strip. If NO fault code, replace membrane, otherwise replace board

I figure you me f7 and f8 here is what the coad means. there is no d8 code.
F7 This code usually means that there is a problem with the keypanel. Many times, it means the keypanel needs to be replaced. F8 This code usually means that the electronic control needs to be replaced.

Good Luck and Please Rate FixYa!

Hey im sorry to hear that...
I fix many ovens., however not really familiar to yours...
However instead of searching for thermostat, try looking for either thermo-couple, falme flaiure device or falme safety device these are the three main termonologies used....

Hope this helps......

Im sorry cant provide you with a full on solution ... but my guess is that your is probably a thermocouple......

F1 means the computer has corrupted....... Part is probably around $150-200 Please rate my help solved as I solved your question.

Here are the codes for Maytag Ranges:

MAYTAG
Type "C" and "D" Clocks Range/Stove/Oven Fault Codes Failure
Code Condition Check/Repair F1 Supervisory relay enable shorted (non-cook mode); sounds alarm and inhibits cook mode if alarm fault monitor is always active in non-cook mode, and requires removal of power until serviced. Usually a bad touch pad or clock assembly (also called the ERC). Replace touchpad or ERC F2 Bake/broil/clean temp runaway alarm; sounds alarm and resets control to non-cook mode when bake/broil/clean temp exceeds programmed limits. Usually means a stuck relay. Electric @ 525F (bake), 640F(broil), 900F(clean)

Gas @ 525F (bake), 640F(broil), 900F(clean) F3 Open temp oven temperature sensor; sounds alarm and inhibits cook mode Replace oven temperature sensor F4 Shorted temp oven temperature sensor; sounds alarm and inhibits cook mode Replace oven temperature sensor F5 Supervisory relay enable open (cook mode); sounds alarm and resets the control to non-cook mode Replace electronic range control (ERC) F5 Missing a/c line cycle detector; displays code (no audible) Unplug appliance for two minutes, should clear problem F7 Function key shorted; too hot at the clock assembly (also called the ERC) or shorted touch pad or clock assembly (also called the ERC) Replace touchpad or ERC F8 Analog/Digital supervisory; sounds alarm to non-cook mode Replace ERC F9 Door latch supervisory (door latched) Unlock door and check switches or clock assembly (also called the ERC) F0 Cancel key supervision Requires the removal of power until serviced. See qualified technician

Sorry to inform you that your oven is on a recall list,here is the link click the link and it may save you a lot!
 https://repair.maytag.com/repair/cooktop.jsp?siteCd=MT_EN_CA

since it is piotless how did you light burner pilots? The oven is piotless and does not have a free standing pilot. here is a link to manual copy and paste page 18 deals with oven. piotless

Try them direct

Manuals - Magic Chef

https://mcappliance.com > manuals Manuals. Product Type: - Select -, Cooking Appliances, Cooktop, Dehumidifier, Dishwasher, Disposer, Freezer, Ice Maker, Laundry, Microwave ... Missing: 458W - ‎44CLW

• Home - Magic Chef

  https://mcappliance.com > magic-chef MC specializes in compact and small kitchen appliances including microwaves, refrigerators, dishwashers, and washers & dryers under the Magic Chef®, ...

If you click on your name it takes you to posting history. Or you can click upper right and click 'My Home'. It was answered. https://www.fixya.com/users/james-dean-88131 ..

Question edited for clarity and create a few sentences. A gas certified technician needs to fit a new thermostat. They can source the part, fit it and check for safety.

This number - 8114P734-60 - is a part number (possibly for the tag it is on). It is not a model. Note: the part number does is not listed in any current parts lookups. Could be a non functioning number or too old to be listed.

get orfices from your gas providers

I don't know. While half a century ago it was common that pilot lights would be permanently lit to provide instant lighting of oven and hobs, because they did consume a significant amount of gas they fell out of favour and spark ignition became reliable. Amid a number of related and unrelated accidents the gas oven began to be seen as potentially dangerous and so they were fitted with a couple of safety devices so for a considerable time the pilot light has to be relit every time the oven is used and the pilot light will be switched off when the oven burners are turned off. Thinking back a long time, the pilots of our old cooker could be turned off using a screwdriver to turn a central service valve hidden under the hob spill tray.

try manufacturer possible replacement number --appliance repair shop -online search

https://www.partselect.ca/Model

HOW-TO: Magic Chef Range CGS3760ADB Won't start or doesn't start

https://www.appliancepartspros.com > ... > CGS3760ADB Won't start

"Won't start" for Magic Chef CGS3760ADB? Here is why, with step by step DIY instructions & videos. s/CGS3760ADB