20 Most Recent
HP LaserJet 5500 Printer - Page 2 Questions & Answers
Hp laser jet printer 2055 ,52 scanner error how can solve it please
The HP Printer error 52 indicates with scanner. When you see the HP printer error code 52, then follow the steps:
·Turn off the printer
·Wait for 30 seconds and then turn on the printer
·In case the 52 error is still coming up on the printer, then make sure that the Flatbed scanner assembly is replaced
·In case the error is still being shown, the Scanner/Laser assembly may also require replacement.
Find the more HP printer error codes and their solutions. If you need any help to fix the issue contact HP Printer experts.
HP LaserJet pro color MFP M276N Network lan port no working
Troubleshoot the wired network connection
Make sure you are using an undamaged Ethernet cable, check for a green light near the Ethernet port on the printer, and then print a report to verify the connection.
Turn off the printer, and then disconnect the Ethernet cable from the router and the printer.
Check the cable for damage, and then verify that it is an Ethernet cable and not a phone cable.
NOTE: Ethernet and phone cables look similar, but Ethernet cables are usually bigger and have eight visible wires on the connector.
Reconnect the cable to a different Ethernet or LAN port on the router, and then connect the other end to the printer's Ethernet port.
Turn on the printer.
Check the lights on the printer's Ethernet port to make sure the connection is successful. The green light should be steady, and the orange activity light should blink.
Print a Wireless Network Test Results or Network Configuration report.
Inkjet printers with a control panel menu: Open the Wireless, Network Settings, or Setup menu to locate the list of available reports.
Most inkjet printers without a control panel menu: Press the Wireless and Information buttons at the same time, or press the Wireless and Start Copy Black buttons at the same time.
LaserJet printers: Press and hold the Wireless button for 10 seconds or until the Ready light blinks, or go to the Wireless menu and select Wireless Network Test.
Laser NS and Neverstop Laser printers: Press and hold the Resume and Wireless buttons for 3 seconds.
DeskJet 6000 and 6400, ENVY 6000 and 6400, and Tango printers: Touch and hold the Information button until all control panel buttons light up, and then touch the Information and Resume buttons at the same time.
Make sure the Network Status is Ready, or follow any instructions to resolve network issues identified on the report.
Regards,
Rachel Gomez
How to clear memory on HP P3015
Before starting, note down the IP address if its network printer..
1. Turn the product off.
2. Turn the product on. When the memory count begins, press and hold the OK button. Continue holding down the OK button until all three product control-panel lights flash once and then remain on. This might take up to 10 seconds.
3. After the message SELECT LANGUAGE appears on the display, press the button or the button until COLD RESET is highlighted.
4. Press the OK button. The product performs a cold reset and then continues its power-on sequence.
5.Chk & set I/O settings..if required..
Cold reset for hp laserjet 3055
cold= hard reset, unplug the machine-- wait 1 minute-- with power off hold down on power button for 1 minute-- plug back in and power up
My HP LaserJet CP4025 has a device failure screen and error code 49.FF03 what does this mean? It will not do anything.
The first course of action with any 49 error is to get the newest firmware installed, if the machine will come to a ready state. Unplug any USB or network cables and power cycle the printer. If it comes to ready, check any computers configured to print to ensure that no stale print jobs are stored in any print queues. (this is an important step, double check that all workstations are cleared). Once you are sure you have all queues cleared, plug the network or USB cable back in and see if printer stays are ready. If it does, go to HP.com and download the current easy firmware installation file for the 4025 and follow the instructions to update the firmware. If the machine will not come to ready even with network/usb cables disconnected then you may have a bad formatter or faulty memory on the formatter.
My printer hp laser jet pro 400 mfp475dn shows error 57.02
Hi
I have taken this directly from the User Guide
"57 Fan error Turn off then on
Description - The product has experienced a problem with its internal fan.
Recommended action
Turn the product power off, wait at least 30 seconds, and then turn the product power on and wait for it to initialize.
If you are using a surge protector, remove it. Plug the product directly into the wall socket. Turn the product power on.
If the message persists, contact HP support."
For future reference this manual can be found here:
http://h20565.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c02966093
and being in pdf format can be saved to the computer.
Hope this is helpful, if so would you please register that with Fixya
Cheers
Not finding what you are looking for?