20 Most Recent
HP LaserJet 2420 Printer - Page 2 Questions & Answers
HP LaserJet 2420 Printer Problem
Go into your print setting and check the box the has 'print on both sides'. It can easily done if you installed the HP toolbox software.
How to fix blank pager printing on hp laserjet 2420
the laser beam is block you need to open the printer and unjammed
since every time you put a toner cartridge there is a fin that moves the cover over the laser or maybe you have a faulty cartridge that the fin is broken
I have an HP Laserjet
I would love to see what the page looks like because I am sure that the word "soiled" doesn't quite mean the same to me as it does to you. See if you can't attach a picture or scan of the soiled side, and also see if you can rub the toner off the soiled side of the page.
Also provide tp/bottom/left/right half.
Thanks.
How can i solve : 49.2f9d service error
On your PC, clear the print queue. Power the printer on and see if the error reappears. If no, there was a corrupted print job in the queue.
Power off printer, unplug the network cable, power on and see if error reappears. If yes, upgrade the firmware
What kind of error is 49.0665
This is a firmware error, that may be caused by corrupt printjobs or network issues. Try to see if you can narrow down the problem to a specific application and also check the URL below for any firmware updates. The problem can also be caused by faulty firmware dimms, memory dimms, or a faulty formatter board, but the message normally persist when this is the case.
Go to htpp://
www.hp.com/
support/LJ4200 or htpp://
www.hp.com/support/
LJ4300. Select Download
Drivers and Software. Check
for the latest firmware image
version at the bottom of the
page. If this firmware image
is newer than the one
installed on your printer and
your printer can receive a
firmware update, download
the newer firmware upgrade.
Not all HP LaseJet 4200/
4300 printers can receive
firmware upgrades.
FF95 SERVICE ERROR CODE IN
Does it give a 49.FF95? As their is no such error code "FF95" for a HP 2420. However I've seen 49. XXXX error codes before (XXXX meaning weird Alphanumeric Characters and numbers). This type of error code you can try a couple of Items:
1st - Perform a Cold Reset:
1. Turn the printer off.
2. Hold down the SELECT button, and then turn the printer on. Continue holding down
the SELECT button until all three printer control-panel lights flash once and then
remain on. This might take up to 10 seconds.
3. After the message SELECT LANGUAGE appears on the display, press the
UP ARROW button or the DOWN ARROW button until COLD RESET is highlighted.
4. Press the SELECT button. The printer performs a cold reset and then continues its
power-on sequence.
5. Check all I/O settings and reset any customer-set printer configuration values
If the machine still comes back to the Strange FF95 error I would start with the replacement of the formatter,
Part Number for the Formatter:
Network versions Q3955-60003
Non-network versions Q3953-60001
Hope this helps..
Print quality problem
Hi there sound to me like the toner cartridge is either faulty or leaking. Is it or has it been refilled if so remove cartridge vacuum out the insides of loose toner install brand new toner cartridge then test again. It cannot be the fuser unit as it will have quality problems all the time so try above and I hope it works for you.
Thanks J
Memory error
Just do 2 steps:
1. Press Stop.
2. If the display highlight "Resume". Press the OK (Check Button).
The display will tell you that a Non-HP Cartridge is installed and Economode is Disabled.
At least, you can now print. The display will show back again to "Ready".
Why is my printer not printing
Your printer may be out of toner, or the drum is not transferring toner to the paper correctly. Try replacing the toner and/or drum in your LaserJet to see if the issue is resolved.
Hp lj2420 errcode 68.2
The printer permanent storage is
full. Some settings might have
been reset to the factory defaults.
1. Press the SELECT ( ) button
to continue.
2. For 68 errors, turn the
printer off, and then turn the
printer on again.
3. If a 68 error persists,
initialize NVRAM. See the
caution and note in To
initialize NVRAM.
4. If this error message persists,
replace the formatter (see
Formatter).
Receiving error 52.00 error. What does that mean?
Here is what HP says:
52.XY ERROR For help press
alternates with To continue turn off then on
Description
A temporary printing error occurred.
Action
- Turn the printer power off and then on.
- If the message persists, contact an HP-authorized service or support provider.
68.2 for 2420
Error: 68.XAn error occurred in the printer permanent storage and one or more printer settings has been reset to its factory default.Remedy:Do initialize to NVRAM.>. Remove Zet direct card if added & other acceries if any added.>. Turn the printer off.>. Hold down the DOWN ARROW button, and then turn the printer on. Continue holdingdown the DOWN ARROW button until all three printer control-panel lights flash once andthen remain on. This might take up to 10 seconds.>. Press the UP ARROW button.>. Press the PAUSE/RESUME button. The display should show SKIP DISK LOAD.>. Press the UP ARROW button until NVRAM INIT is highlighted.>. Press the SELECT button. The printer initializes NVRAM and then continues its power.> Check if its not resolved replace formatter assembly...
Not finding what you are looking for?