Top 20 Braun Hand Held 120 W Mixer Model 4169 In Good Used Condition Questions & Answers

i could not find a user manual but follow this link to a schematic of the machine and its parts numbers hope this helps youhttp://www.1800parts.com/images/1800Parts/English/products/standard/4169-Schematic.pdf

Somewhere deep inside on the shaft will be a shear pin.

Service and parts manual https://manualzz.com/doc/22473309/service-documentation-braun-kitchen-machine-km-32-b-4209-... For the owner's manual, after a considerable time searching, it says to contact Braun direct! https://www.service.braun.com/ca/en/product/product.html?typ=guide&s=KM32&seite=&sString=4209'HH'HH04'H'&subgrp=&grp=0&frmTyp=s ..

Google name and model

I understand the KM32 mixer uses 4.5 oz of Food Grade Mineral Oil in the gearbox, but haven't found a source. Will try Restaurant Supply house or appliance repair.

Did you get it fixed? If you haven,t, let me know and I'll show you how I fixed mine. [email protected].

Hi, my name is John I will do my best to assist you.

Knowing the model number of your mixer will be helpful in trying to locate an assembly diagram, and part info to better assist you. Please provide the model number.

General Suggestions

As you may be aware your mixer has a safety feature that disables functionality if the unit gets to hot due to overloading. If this may be a factor and you haven't already, unplug the mixer and let it rest for at least an hour and then try it again.

You mentioned that the motor is working but the attachments don't turn. Some mixers are equipped with an mechanism that will only allow drive from the motor to engage if the attachments are firmly locked in place. The problem may be here.

If the unit was overloaded, it is possible that the plastic gears were damaged. Unless I can locate an assembly diagram of your specific model I will be unable to give you more detailed information.

If you feel comfortable with a trial and error approach you could carefully disassemble the mixer for closer examination. Most mixers housings are held together by 4 or so screws. Be careful when separating the housing halves as some parts may disconnect, or detach. If you open it slowly and pay close attention you should be able to see how things are assembled, and understand how they are going to come apart. Make notes for reassembly.

If you find that the gears are damaged, you will most likely have to contact the manufacturer to locate replacement parts.

If you have more specific questions please post comments to this thread and I will endeavor to monitor new activity and respond as soon as possible. I recommend that you "bookmark", or "add to favorites" this page for your convenience.

This sounds to me like the brushes in the motor need to be replaced. You may want to call an area shop which rebuilds electric motors and see if they have a replacement for you. They're not very expensive and fairly easy to replace.

I hope this helps and I hope you have a wonderful holiday season!

-Jason

I have an extra bowl, but am in need of a regular whisk...any chance you have an extra and we can trade?

Model # please

check the warranty? it may be still covered, sounds like a replacment switch/unit required.

most likely would be less expensive to buy a new one

You will need to get a qualified electronics technician to look at it. The issue could be anywhere on the circuit boards inside the mixer. Unless you know what you are doing don't try to repair it yourself as you could make the problem worse.

Spray some WD40 into the eject button. The wait 10 minutes and turn it upside down and spray WD40 down the side of the beaters Leave 10 minutes and try again/ If that doesn't work, you will need full disassembly ..

Please state whether user or maintainance manual.

Contact them direct. No one sells them online. Or most cities have a drive belt supplier. Take in the old one and say 'can I get one of these'. There are 8 places near me! https://www.google.com/search?q=drive+belt+suppliers+near+me

Food Mixer BISTRO Black - Kitchen Appliances

Bodum https://www.bodum.com > 11381-01us-3-bistro The food mixer BISTRO Black has a 7 speed motor up to twice the power of traditional stand mixers. Its attachments are also dishwasher safe. Bake in style! US$103.99 https://www.google.com/search?q=Bodum+Stand+Mixer+11381+belt ..

Question edited for clarity. The drive train probably need cleaning and re-greasing, but there is also a gear that wears out. https://www.google.com/search?q=Kitchen+Aid+Mixer.+How+to+fix+a+grinding+sound+when+switch+is+on+Medium+speed ..

Push the head down before pressing the button on the mystery mixer. There is probably dough under the hook with it pressing the head up and is locking the catch. You can pull out the dough around the dough hook to make it easier. All questions need 'make model (what it is)', first 3 words please

Question edited for clarity and toss in some CAPS. Remove the bowl. Push it upwards and turning at the same time to centre it. Or remove all the screws, drop it down, clean it and put it back. https://www.google.com/search?q=thunderbird+arm-20+remove+guard ..

All question need full 'make model (what it is)' please. Duplicate question deleted. Press Refresh to see your question. The only thing we know it that is made by Sunbeam and it MAY be a food mixer because that is the category it is posted to. Look at what is there already. It is black and greasy, it will be GP Graphite Grease. If it is white and greasy, you can use white Lithium grease in spray or tube. If it looks like normal oil, use 3 in One. This is a service manual for a vintage mixer, it say to use a special grease, but from the description high temperature bearing grease would work. https://studylib.net/doc/25985112/instructions-for-servicing-vintage-sunbeam-mixmasters Nothing based on the the quoted words. https://www.google.com/search?q=Sunbeam+power+unit+lubricant ..