20 Most Recent Hobart Mixer Only, Planetary, Bench, 12 Qt., HL120BUILDUP - Page 6 Questions & Answers


Could Could the anti syphon blocked? I'm guessing the drain pump doesnt operate while this happens

Hobart... | Answered on Jan 16, 2018


Water pump. This may be clogged or wrecked. Normally clogged. http://kitchen.manualsonline.com/manuals/mfg/hobart_corp/lxih_ml_130017.html?p=18

Hobart... | Answered on Jan 14, 2018


Yes, you must use chemicals in commercial machines for a number of reasons.

Hot water alone will not remove grease and food residue.

Without Rinse Aid, plates and glasses will dry with spots on them. You will also get scale build up very quickly. Rinse aids breaks the surface tension of the water and makes the water film off and evaporate.

In a commercial situation, you will be in contravention of food hygiene regulation.

Most machines have an alarm sensor that will beep if there is no detergent sensed.

There are two types of dishwasher, those that use hot water rinse sterilisation at 210'F rinse or those that use warm or cold water and a hypochlorite bleach sterilizer. Without that, you risk being a source of food borne illness.

Andrew - Chef, catering manager for 48 years :>)


Hobart LX18H Manuals

Hobart... | Answered on Jan 12, 2018


Long shot, but have you checked to hood reed switch. Nothing will happen if it thinks the hood is open?

Hobart... | Answered on Jan 11, 2018


A constant electric supply normally means the relay that switches the component is faulty. This would normally be the timer or relay board, depending on how it is switched

Hobart... | Answered on Jan 09, 2018


Sounds right. The level may be an issue with fill solenoid rather than tank floats. Also, is the drain overflow blocked?

Hobart... | Answered on Jan 06, 2018


Steam traps have water in them? Might be wet steam, as daft as that sounds

Hobart... | Answered on Jan 06, 2018


Hi SubaruB4
it may be the electric valve where the water comes in if it doesn't open when switched on water wont enter

Hobart... | Answered on Jan 05, 2018


Error 09 is boiler not filled.If the element had blown, its like this was due to the fill solenoid failing.

Hobart... | Answered on Jan 05, 2018


UL means there is too much water in the wash tank. It will continue to run the drain pump u ntill the water level is correct. If it is not pumping out then there could be a problem with the pump, blockage or relay fault on pcb

Hobart... | Answered on Jan 05, 2018


You'd need to check continuity of the elements in the boiler. Does the machine cycle at all?

Hobart... | Answered on Jan 04, 2018


Convayor motor overload switch or table end switch if one fitted

Hobart... | Answered on Jan 03, 2018


Boiler possibly not reaching temperature.

Hobart... | Answered on Dec 02, 2017


Needs a boiler fill sequence carried out. Will tell you how in the manual

Hobart... | Answered on Dec 02, 2017

Not finding what you are looking for?
Hobart Mixer Only, Planetary, Bench, 12 Qt., HL120BUILDUP Logo

1 questions posted

Ask a Question

Usually answered in minutes!

Top Hobart Dishwashers Experts

GPEC

Level 1 Expert

12 Answers

Jason

Level 2 Expert

218 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Are you a Hobart Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Hobart Dishwashers

  • Hobart Dishwashers

Most Popular Question

when mixing pizza dough in hobart se 601

  • Dishwashers
Loading...