20 Most Recent Hobart CL44e-2 Conveyor High / Low Temperature Dishwasher with 30 kW Booster Heater - Right to Left Operation - Page 9 Questions & Answers

0helpful
1answer

Hobart dishwasher cl64e is stuck in rinse cycle

Just a guess here... Mike Lovelace, But your "DELIME" procedures have not been followed and/or your dirty water detector needs to be cleaned or replaced... Contact HOBART 701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART • www.hobartcorp.com Alternatively look up WHALEY Food Service or Heritage Parts... Hobart Parts Distributor Heritage Parts Whaley Parts Manual HOBART CL64e Hope this helps Carnac the Magnificent
10/17/2017 1:38:25 PM • Hobart... • Answered on Oct 17, 2017
0helpful
1answer

What does es stand for on commercial hobart dishwasher

Hello Antoinette Badra, Hobart is one of those FEW names that seems to have survived with a STERLING REPUTATION... intact (uncommon... ). Unlike KitchenAid, KENMORE & Maytag (opinion: personal experience). ((If you are thinking about a WINE COOLER and you DRINK anything bigger FORMAT than "TWO BUCK CHUCK" ... bring a bottle to VERIFY you cannot fit it into KitchenAid (KUWL304ESS, KUWR304ESS = pathetic))). Used to have a HOBART dealer right here on TELEGRAPH Avenue in OAKLAND 9, Calif.... (Oakland used to have PRIDE TOO)... Where I was delighted to find ... not only competence, parts & integrity... but PRIDE and they did not mind some curious child (me) who was interested in repairing THEIR (commercial grade) equipment. So it was with a bit of JOY that I undertook your question to find where my OLD FRIEND had gone... After EXTENSIVE reading... I find that HOBART is not just ENERGY STAR® compliant... They are a "PARTNER" and a 2015 AWARD WINNER... So... without the benefit of a MODEL NUMBER 9usually required to speak intelligently)... I will have to guess: ENERGY STAR® = "es" Hope I am helping Industrial Washers Apocryphal (?): https://en.wikipedia.org/wiki/Hobart_Corporation I'm just saying... Every once in a while some designs make it past the ACTUARIES... (hidden quality wins over fast & cheap). Carnac the Magnificent
10/17/2017 1:12:39 PM • Hobart... • Answered on Oct 17, 2017
0helpful
1answer

I am working on a Hobart SR24H dishwasher. The cycle starts but the fill valves are not energized and no water is being allowed into the system. The hot water booster tank is heating up.

Hello Jim Richards, I tried to pull down... any meaningful information from the GARDEN VARIETY part houses... It appears you can get replacement parts through grainger... Manualslib.com does indeed show SR24H a commercial grade unit... (also SR24C... similar chem clean commercial grade) Hobart SR24C Instruction Manual Page 4 Hoping to find valves, schematics & perhaps even PART NUMBERS... (no luck). Found some parts on the internet... Parts list (Rev A, August 2009) http://www.hobart.com.mx/pdf/CatPartes/F43078RevA_Lk.pdf I don't know if you have tried to "activate" the valves (power direct to... VALVES not responding = open coil) Or you are having a control board failure (test for voltage present)... If you have power at the valves... and they are merely not responding... Some folks will tell you to clean the (descale.... decalcify) your VALVES. I'd say replace them... NOT CHEAP (but it appears "KITS" might be available) then play with the old ones at your leisure... (obviously... if that I indeed your issue) Grainger.com might help (but not obvious on the net) Heritage parts, WhaleyFoodService and Partstown (appliancepartspros was a COMPLETE BUST) see below https://www.bing.com/search?q=hobart+sr24h+parts&form=EDGEAR&qs=PF&cvid=dc8dfce20e70486cbcb3a4149b58c984&cc=US&setlang=en-US&PC=DCTE Whaley Parts Manual HOBART SR24H
10/17/2017 1:59:16 AM • Hobart... • Answered on Oct 17, 2017
0helpful
1answer

Hi I have a Hobart LXIH dishwasher and it is leaking water out of the bottom corners of the door. Do you know what might be causing this?It has a seal at the top but no seal on the sides or bottom.

Make sure your rinse wash arms have the end plugs. If one is missing, water will spray out door.

Your fill valve could possibly be malfunctioning, therefore not closing all of the way. I used to work for Hobart. These LX machines can be a pain in the rear. If you have a water softner, then the valve is probably functioning normally. I do not recall it ever being the door gaskets. I would think you should be getting an error code with the wrench. This is a hot water machine. If you have lime scale building up inside, you may try deliming it. The drain valve could be also causing a problem. There are so many things it could be.
10/16/2017 4:30:00 AM • Hobart... • Answered on Oct 16, 2017
0helpful
1answer

HOBART MODEL 1912 WEVE HAD IT FOR 14 YEARS IT NEEDS TO BE SHARPEN. I DO NOT KNOW HOW

I think you can get all of the parts for that to replace it instead of sharpening it.
10/6/2017 9:22:03 PM • Hobart... • Answered on Oct 06, 2017
0answers
0answers
0helpful
1answer

Hobart AM15 dishwasher is not getting to 180' on the sanitizing cycle. How can I increase the temperature? Presently, centers around 177' when it is sanitizng

Try running the hot water into the sink immediately before you turn on your dishwasher. That will get hot water from your heater to dishwasher faster & help with the sanitizing cycle heat
9/7/2017 12:21:49 AM • Hobart... • Answered on Sep 07, 2017
0answers
Not finding what you are looking for?
Hobart CL44e-2 Conveyor High / Low Temperature Dishwasher with 30 kW Booster Heater - Right to Left Operation Logo

1 questions posted

Ask a Question

Usually answered in minutes!

Top Hobart Dishwashers Experts

Cindy Wells

Level 3 Expert

6688 Answers

vince

Level 3 Expert

2530 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Hobart Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Hobart Dishwashers

  • Hobart Dishwashers

Most Popular Question

hobart dishwasher cl44e showing disply

  • Dishwashers
Loading...