Sunbeam Twin Electric Auto Heated Blanket- Mushroom BW9800-030-772 - Answered Questions & Fixed issues

Would be better if Make and Model was mentioned, but this says it is a grounding issue. https://www.google.com/search?q=heated+blanket+controller+is+flashing+green ..

Wires should be on the floor. Do not put them where you may lay on them and or cause friction on them (even if it's just rolling over during the night).

Question moved from Car Accessories to one of the Electric Blanket categories. Almost impossible without a make name. That type of replacement only come from the manufacturer. Nothing is coming up on that model number. https://www.google.com/search?q=MODEL+2140+mattress+cover%2C+replacement++controller ..

plug it into a power strip

Try contacting the manufacturer for replacement. Or try fixing the one that does not.

Haven't you contacted the company that shipped it to you? It might have been an oversight and they'll mail you one. You can do that for anything you get shipped to you from a company.

Sunbeams - blinking "F" means that the connection to the blanket was loose. Make sure you give it a good push to get the piece fully engaged.

Wd 40 spray it down really good then wipe excess. Let dry

No . Get rid of it, they are not safe anyway.

Sure, here are a few suggestions on where to find a replacement controller for your Sunbeam BL0750 electric blanket:

* **Sunbeam customer service:** You can contact Sunbeam customer service directly and they may be able to help you find a replacement controller. Their contact information is available on their website.
[Image of Sunbeam customer service website]
* **Online retailers:** There are a number of online retailers that sell replacement controllers for Sunbeam electric blankets. A quick search should turn up a few options.
* **Local hardware stores:** Some local hardware stores may also carry replacement controllers for Sunbeam electric blankets. It's worth checking with your local store to see if they have any in stock.

Once you've found a replacement controller, you can either install it yourself or have a professional do it for you. If you're not comfortable installing the controller yourself, you can take your blanket to a qualified electrician or repair shop.

Here are some additional tips for troubleshooting your Sunbeam BL0750 electric blanket:

* Check the power cord to make sure it's plugged in securely.
* Try using a different outlet.
* Check the fuse or circuit breaker to make sure it's not tripped.
* If you've tried all of these things and the blanket still doesn't work, you may need to replace the controller.

I hope this helps!

There is chance that arcing brushes in the motor are causing the odor. They should be replaced and the armature cleaned. A sunbeam repair shop can refurbish your mixer if the parts are still available.

Nothing works. Have had it for 6 months. Plugged in after so long, still blinking.

compressor not working or low on freon

A partstore knows or chec online

heating element possible shorted out.

Try these: -Make sure the remote battery contacts are clean; -clean fully charged battery surfaces with a lead pencil eraser to remove oxide; -could be loose contacts or cold solder joint on remote control board, especially if dropped a lot. if not tech savvy probably better to recycle old unit and purchase a new one . good luck!

Generally means u have a bad connection at the wall or at the control module. Disconnect everywhere u can and reconnect

Possible free manual if this is the same model with wick information. http://www.milesstair.com/Sunbeam3602.pdf

Try unplugging the power cord from the wall socket and check that the connection to the blanket is good and not loose. Then plug back into the wall socket and switch on. If error still occurs then there may be a problem with the blanket.

My sunbeam XL heating pad started blinking and I couldn’t figure it out. I Unplugged a couple of times and still it kept flashing. After hours of reading post, I did what wpart suggested and now it works normal again..... I kept pushing th on off button while plugged in, I unplugged it while still hitting the on off button, I plugged it back in while still hitting the on off button annnddddd drum roll please!!!!!! It started working properly! Thanks wpart, your the MVP and award goes to you!