Zanussi 24 in. IZZI ALU Built-In Dishwasher - Answered Questions & Fixed issues

If it trips after a few minutes of coming on , it is probably the heater which is faulty , disonnet it and try , if it doesn't trip you need a new heatee

try this link: Cafe Retro 1385 Electra craft com

Hi

The issue can either be with the unit not draining properly or the timer/electronic board itself has gone bad & should be replaced. First clean the drain hose and the drain pump for any clogs, you can do this by taking off the bottom access panel. After cleaning if still the issue is not resolved then the timer/control board has gone bad and needs to be replaced. Hope this helps...please post back for further assistance.

Daniel

did u ever get this sorted and wat was the problem??? mine is doing the same!! any help wud be great ..

Hi,

Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - Water will not drain outheatman101

Turned out there was a block on the clear short pipe that goes to a pressure sensor situated to the left at the front behind the front facia under the door which the engineer cleared by blowing it!! The pipe connects to a little stub that sticks out of the blue plastic flow control thing on the lhs of the dishwasher. U can access this by removing the lhs cover but not really necessary...

It sounds like you have eithwer a low water problem (ie..Clogged inlet valve ) or your heater inside the unit is bad are they drying ok one other thing to do is run the hot water at the sink first to make sure the cold that is in the lines from the water heater is not filling in the unit try those things first

A flashing start button shows that the filter is dirty. Remove the filter assembly from the machine. The "tube" can be split into 2 sections fairly simply - do so, and wash each piece under the tap to clean it.
Once the assembly is cleaned properly, select the program that you desire, and press and HOLD the start button for 2 seconds. The wash cycle should begin.

Dishwashers are suppose to be hooked up to hot water. If you had hotter water it would clean just fine. 120 deg or more!

exercise to lose belly fat; fat loss extreme; workouts to lose belly fat; best foods to eat to lose weight; diet for weight loss for female; dr now diet plan; simple 1200 calorie meal plan; meal plan for weight loss and muscle gain female; 1200 calorie a day meal plan; lifting weights to lose weight; foods to eat to lose weight; lunch for weight loss; healthy lunch for weight loss; healthy foods high in fat; https://behealthyideas.com/ <ahref="https://behealthyideas.com/">https://behealthyideas.com/</a>

If it is new, it is under warranty and if you try to fix it, it will void the warranty. The water in the flood tray comes from the machine itself, normally from hoses or on an older machine pump seals. Page 17 refers and confirms https://manualzz.com/doc/53457617/zanussi-zdln1512-user-manual Call for warranty service to fix the fault free of charge.

input to pump clogged output clogged pump bad or just dirty inside. leaks end to end that path, In and output.

Under the base of the machine, above the floor there is a tray with a sensor in it and that is what triggers the Flood Error Code. So the machine needs to come out, the back or side panel removed and the tray thoroughly dried. You also need to find where that water came from. If the salt container is in the base, it may be leaking if you were breaking up the salt.

get a tech out there, as these appliances get more sophicated, they become nightmares its best to buy a basic model

There is no external adjustment in a dishwasher.

Bad timer zz

It is normal that after adding the salt it takes time to dissolve, which means that the salt lamp will be extinguished after several complete washing cycles. Dado

Pull it out of the cabinet and they are all there.

Since it is brand new, you should be able to request repair, replacement, or refund under the warranty.