Top 20 LG Dehumidifier LD650EAL Questions & Answers

Could be low on freon or humidestat is bad..

It appears as if the water may not be flowing through the hose. * When you use a hose the unit must be located near the drain. If the hose is to long the water will not flow freely and cause the water to back up in the hose triggering the bucket full. * If the unit is lower or the hose runs up hill even the slightest incline will cause the water not to flow backing up to the machine * Hose must remain flat and in a down hill flow to the drain if you are running a longer hose than recommended. If you are have a long distance to run the hose elevate the dehumidifieer by placing it on a stand, milk crate, anything that will hold the unit. Be sure it is large enough and strong enough to support the unit to prevent it from falling. This will help siphon the water from the unit and prevent any water to back up the unit. * If your using an old hose make sure there are no kinks and water flows freely through the hose. Any kinks or type of pinch in the hose will cause the water to back up I hope this helps resolve your issue. This is the most common mistake when using a hose.

I had the same problem. For me the fix was to take all the covers off, remove the bucket switch, clean the contacts on the switch, and i poured alcohol all over the switch and repeatedly pressed on the actuator . I dried it all off, put everything back and it worked again like a charm.

Question edited, toss in a load of CAPS. The capacitor is likely to have failed internally. It can still produce voltage. Or the transformer that supplies power has failed. No one else has recorded this issue https://www.google.com/search?q=LG+Dehumidifier+model+LHD459ELY9.+No+power+to+the+display ..

https://www.searspartsdirect.com/manual/44av6atl6i-003204/lg-ldf7551st-dishwasher-parts?sid=sem:ggl:dsagroupb:141452280898::c&keyword=&gclid=Cj0KCQiAtICdBhCLARIsALUBFcHCsKc_OEAYHAPPbyS-9LcLCYIAojCvzFzeIbtp7dOcMwOBVditVK8aAhxCEALw_wcB

The bucket is drained continuously with hose connected - no need for "full" sensing

the drain hole(s) are blocked up. Needs cleaning

Hello everyone, can someone please tell me what is error code CH10 on lg dehumidifier please?
Thank you

Is the other end of the hose BELOW the level of the bucket?

Go to LG's website to look at the recall list.

Heating up ? are u saying the fans not running (there are two fans inside) id look into why the fans aren't running , only one the speed is adjustable the other is not it runs solid speed all the time

Here's a link to an article written by a service technician with more than 30 years of experience. It gives details on How to Clean Dehumidifier

make sure the bucket is in the right spot LG LD651EBL Owner Manual Page 15

if thats where you run it at 40 i suspect it's overheating and shut off possibly broken now , one should never set a humidistat less than say 66%rh as a normal house is 70%rh and asking anything more of a home unit is just not possible if moisture is that much a problem try running two units about twenty feet apart , they will cycle more to cool down and will run longer , might even be more efficient than running one harder

totally dead, check fuses. could be stiffened up over the time and took fuse out on first switch on

You can't, it uses freon.

Try resetting the GFI breaker, assuming it is connected to one. Also check the main breaker panel to make sure the breaker is not tripped. Unfortunately the electronic panels do go bad in these systems after a few years of service. Try resetting the unit. There should be a tiny reset button on the back. Also if the bucket is full it will not turn on, make sure it is in place and seated properly or it will not turn on. There may be a reset on the cord itself as well, hope this helps.

Sounds like a refrigeration problem, I am assuming the fan operates. Unplug it and let it set for about an hour. Plug it in and see if the compressor starts. If it does and you do not get water It is either low on gas or the compressor has failed. If the compressor does not start but hums it would need a new capacitor. If nothing the thermal overload has probably failed. This should get you started. Good Luck. If it is to involved they are not that expensive to replace.

Look in the owners manual for codes

did you try taking a qtip and cleaning any gunk on the inside plastic hose? That just happened with mine and I am giving it a shot. Had a ton of brown stuff blocking the pathway. I jsut do not know where the genesis of the hose is, so I could only get in so far. Let me know how it goes.