20 Most Recent Zanussi ZMC30STQX Convection Microwave Oven - Page 8 Questions & Answers

Give them a call at their 800# https://www.sharpusa.com/support.aspx

A "FAIL" code on a Galanz microwave typically indicates a problem with the electronic control board. This can be caused by a variety of issues, including a malfunctioning sensor, a software error, or a problem with the power supply. It's recommend you to unplug the microwave for a few minutes and then plug it back in. If the problem persists, you should have the microwave checked by a professional technician. You can also try to reset your microwave by following the steps in the user manual, which typically involves pressing a certain combination of buttons on the control panel. If the problem is still there, it is advisable to contact the manufacturer or a professional technician for repair. This will help you to get a more accurate diagnosis and a solution to the problem. Depending on the cause of the issue, the cost of repair can vary.

https://www.reddit.com/r/YouShouldKnow/comments/s5in5m/ysk_download_pdf_versions_of_all_of_your_better/hszrugv/

Look for a fuse on the back where the power cord enters. If not, this is the fix https://www.fixya.com/support/r29874712-repairing_microwave_ovens ..

The issue you're experiencing with your KitchenAid microwave/oven combo sounds like it may be related to the door not being properly closed or latched.

1. Check the door: Make sure the door is closed tightly and securely. If the door is not properly closed, the microwave will not work.
2. Latch: Ensure that the door latch is in good working condition and securely latched when you close the door.
3. Door switch: If the door is closed and latched properly, the problem may be with the door switch. A malfunctioning door switch can prevent the microwave from starting.
4. Control board: The issue may also be caused by a malfunctioning control board. The control board is the brain of the microwave, and if it's not working correctly, it can prevent the microwave from functioning properly.
5. Wiring: Check the wiring of the microwave, if the connections are loose or damaged it could cause the microwave to not work.

If none of the above steps resolves the problem, it's best to contact the manufacturer or a professional for further assistance, as these are complex appliances and require specialized knowledge to repair. It's important to note that attempting to repair an oven or microwave without proper training and tools can be dangerous and could cause further damage or injury. Hope this helps!

You can try contacting the manufacturer of the oven, NOBEL, to see if they have a digital copy of the user's instruction manual that they can provide to you. Additionally, you can check the website of the company or try searching for the manual on the internet to see if it is available for download. If the oven is no longer in production, you may have difficulty finding the manual, in that case you can try searching for a similar model manual, or try reaching out to a repair shop or appliance store that specializes in the brand.

Try holding down the stop/reset button until it beeps. If this does not stop it from turning on/off automatically then you may have a loose connection in the wiring between the inverter, magnetron, and/or control board, or one of those components have failed. Because of the lethal voltages used and produced with inverters, I do not recommend that an inexperienced person repair it.

It is combi oven sanuzzi model electrical fcz061eba2

Kent https://www.fixya.com/support/r29874712-repairing_microwave_ovens ..

It sounds like there may be an issue with the high limit valve or the temperature sensor in your broaster. The CHECK message and the "high limit valve close" message may indicate that the broaster is shutting down due to an overheat condition. You may want to check the high limit valve and temperature sensor to make sure they are functioning properl

no info generic answer ---fixya will be unable to give you assistance since no info and cant ascertain damage if broken replace if

Doesn't appear to be a well known make. https://www.google.com/search?q=Speed+Chef+convection+Oven+manual It is also the name tagged to commercial ovens. https://www.google.com/search?q=Speed+Chef+Oven ..

Question edited for a hell of a lot more clarity. All question need 'make model (what it is)' please, first 3 words. It literally could be anything. The only thing you can try is a power cycle or check the back for a fuse holder near the mains lead. https://www.fixya.com/support/r29874712-repairing_microwave_ovens ..

Question edited for a lot more clarity. All questions need FULL 'Make model (what it is)', first 3 words. F82 means there is no power being supplied to the lower high voltage transformer. It may be due to: - failure of relay RY-4 on the circuit board - 10A fuse open - controller failure Note this regarding the High Voltage Transformer https://www.fixya.com/support/r29874712-repairing_microwave_ovens ..

Incorrectly heat treated. Contact them for a warranty replacement.

Had you set the time if it had no time programmed in it didn't have anytime to run.

It could be something as easy as adjusting door microswitches, but equally it could be the transformer or magnetron. Look for a fuse near the wire at the back https://www.fixya.com/support/r29874712-repairing_microwave_ovens ..

I would type the make and model into the gargler for a chance of getting one.

claim on the warranty https://www.google.com/search?q=Galanz+Speedwave+microwave+Error+30 ..