20 Most Recent Canon MultiPASS MP730 All-In-One InkJet Printer - Page 2 Questions & Answers

To reset waste tank full error in MP730.

1. Press the "menu": Key
2. Press "Copy" Key
3. Press "#" Key

4. Scroll thru the menu headings until you come to "Test Mode" - 12th heading or select (-) as a short-
cut to the last setting.
4a. Press "Set" and the display shows:
Test Mode [1] - [8]
CF-FH3 :WLD-11-02

4b. Press "8" and the display changes to:
Test Mode [1] - [8]
Please wait

***note*** you have to wait until the display changes

Then the display changes to:
8: PRINTER TEST
[2]---[8]

5. Then Press the "3" button and the display shows:

8 - 3 : EEPROM Clear

*** the display scrolls to [0] : INK COUNT
[1] : 2PURGE FLAG

6. Press "0" button - for INK COUNT
7. Press the "Stop" button
8. Press Off then On to set new changes.
9. Printer feeds a blank page after it is turned on again.

This should Reset the printer and remove the WRONG CARTRIDGE error and save you a few dollars.

To fix this you first need to remove the ink and the print head.Wash the 4 ink pads in luke warm water.Keep running the water over the bottom of the print head until the water shows no sign of ink colouration.Make sure all of the print head is completely dry before replacing it into your printer.After restarting your printer you will probably see the alarm light still flashing.Now hold your finger on the resume button for up to 2 minutes or until you hear a clunking sound.Hold your finger on this button and the printer will fix itself and the alarm light will stop.

if your cartridge is damage or blocked, it do that. get a new cartridge to test it.

Use a small flash light and check for any debris blocking the roller from the tray...

Hi Sandra,Follow these instruction in attached images.

I think I know why. You need to set the proper priority of your all-in-one Canon device. If it is TEL priority, it means you need to have a phone connected to the fax. If the phone rings, you need to pick up the handset and check if it's a fax tone or a call. If it is fax tone, you wait for 5 secs til fax tone stops, and then hang up. After that you will receive the fax. Failure to pick up the handset will not allow you to receive the fax. This might be the most probable setting you have, hence you can't receive the fax.If it is FAX priority, the same thing happens as TEL priority. Only difference is if you don't pick up, and it is a fax, it will still receive.You can also do FAX only. No need to connect a phone. Device will receive automatically.-Acieboy

Blue wire or green wire? If you have trouble with your color vision, have somebody else verify this. Green wires (or green wires with yellow stripes) with ring terminals (especially if they have teeth like lock washers) are used for electrically bonding the metal parts of the system to the ground terminal. In that case, you would look for threaded holes in the metal parts of the frame.A blue wire may go to a screw terminal block, typically for the hot terminal from the AC power connection along with a brown wire for neutral, but screw terminal blocks are rare in desktop printers. More commonly the AC power goes through a nylon two-pin or three-pin connector that mates with a corresponding connector on the power supply board, and the AC wires are usually black and white instead of blue and brown.Hint for future projects: When I remove a grounding wire from a chassis, I put the screw back in the hole (several turns, not tight) to remind me where the ground connection goes. (A loosely inserted screw not holding anything is waiting for that wire.) If you really want to be sure, tie a green thread around the screw, and remove the thread when you are ready to replace the grounding wire.

You may need to buy black ink cartridge because it maybe empty anyway...buy new black ink cartridge and replace the old empty one

Hello, Bernard.

Sounds like a problem with the driver. Download and install the latest driver.

http://www.usa.canon.com/cusa/support/consumer

1. Select the 'Product Type' from the Canon web site Support & Drivers page.
   
   
2. Select the 'Product Family'.
   
   
3. Select your 'Model'.
   
   
4. Click on 'Drivers & Software'.
   
   
5. Select your Operating System (i.e. Windows, Mac OS X...etc.) from the drop-down menu.
   
   
6. Click the driver you wish to download.
   
   
7. Click 'I agree - begin download' at the bottom of the page.
   
   
8. To download the file:
   
   Windows: Click the file link, select 'Save', and specify the directory where you want to save the file. The download will start automatically.
   
   Mac: Click the file link, the download will start automatically.
   
   
9. Windows: Downloaded files are saved in the folder you specified in a self-extracting form (.exe format).
   
   Mac: Downloaded files are saved on the desktop as a disk icon.
   
   Ex.:
   
   
10. Double-click the file or disk icon to decompress . A new folder will be created in the same folder as the downloaded driver (Windows) or on the desktop (Mac), or the installation will begin automatically for some models. The new folder has the same name as the decompressed file.
    
    
11. Open the folder, then double-click the decompressed Setup.exe file (Windows) or .Setup (Mac) to start installation.

Hope this helps.

In most cases the printer driver software can have errors while being in use or is shut down. So to reset remove your printer from the PC and uninstall the printer software. Now reinstall the printer software and then connect the Printer to be detected as a new hardware as it will be installed. Now check the printer properties to see the ink levels.
Activate head cleaning before a test is taken . Sometimes it is possible that the head is not reacting to the need of the PC command or can be an issue with ink drying or poor ink cartridge contacts. Sometimes the power supply unit must be checked as a poor SMPS unit can deliver low voltage and cause issues to the printer function. Check all the leads and connections of the mother board , the tags to the ink cartridge. Also check the mechanical settings of the ink cartridge , if jammed or tight remove motor and manually free the drive before it is set back.

Thank you for using Fixya

Hi mserio007,

Please perform a deep cleaning.

1. Press the button on the printers operation panel.

2. Press the left [] arrow buttons to select [MAINTENANCE].

3. Press the button.

4. Press [] to select the cleaning setting you want. Select [HEAD CLEANING] for normal print head cleaning. Select [HEAD REFRESHING] for deep print head cleaning.

Note: [HEAD REFRESHING] uses more ink than [HEAD CLEANING], so perform [HEAD REFRESHING] only when necessary.

5. Press .

6. Print a Nozzle Check Pattern and perform at least two Head Refreshing if the pattern is not correct.

If this does not work, then It seem the contacts on the print head are damaged and you have to replace the print head to resolve the issue. But before that you can follow the steps below to remove the print head and then cleaning the copper contacts on them with a cotton swab dampened in distilled water until they are clean after drying them check the issue if the problem persist then replace the print head to resolve the issue.

1. Make sure the power is turned on.

2. Press [Open] and lift up the scanning unit. The print head holder automatically moves to the center of the machine.

CAUTION:

Do not try to manually move or stop the print head holder.
Do not touch any metal parts.
Press on the tab to release the ink tank, then remove it from its slot. Repeat this process until all ink tanks have been removed from print head.

3. Lift up the lock lever and take out the print head.

4. Reinsert the print head.

5. Insert the ink tank into the empty slot on the print head. Press down gently on the top of the tank until an audible click is heard. Make sure the ink tank is inserted into the correct color slot.

6. Close the scanning unit until it locks into place.

7. When the LCD displays [ALIGN PRINT HEAD], press on the operator panel. The machine will print a horizontal line pattern, and the LCD will display [CHANGE H VALUE] on the top row and [A 0] at the bottom row.

(A): Column A
(0): Value for Column A

8. In column A on the printout, note which box has the most solid image. Note the value next to this box and use [Left cursor] or [Right cursor] on the operator panel to enter it then press .

9. Repeat step 9 for columns B to K.

10. When values for all columns have been entered and the LCD displays [PRINT VERT. PATTERN?] on the top row and [YES=(*) NO=(#)], press [#] to return to standby mode.

Hope it helps.

Thank you for using FixYa.

Hello there, your printer has encountered a system error. the first thing you want to do is try to cancel all print jobs which have been sent to the printer. Next you disconnect the unit from its main source of power for about 15 to 30 mins. When this has been done the printer should reset itself automatically. Any system errors which has occurred on the printer would have reset itself within the time frame. If it is connected to a PC uninstall the driver and restart the PC before reinstalling the driver again. After all of this the unit has reset itself and cleared all errors which might have been the cause of the problem. If this does not solve the problem then you need to refer the unit to the nearest canon center as it indicates the problem is hardware related and might need replacement parts.
Hope this solution has been helpful?
Thank you for visiting FixYa.

Hello,
You could try taking some paper towel, wet it a bit and sit the cartridge on it. Also take a look at the electronic contacts on the side of the cartridge. Make sure they aren't dirty, and if they are gently wipe them clean. Sit the cartridge on the wet paper towel and let it soak a bit then put it back in the printer, and do another head clean from the printer settings. This should moisten the micro ink holes and hopefully free any clogged ink particles.
If it still doesn't work, the printer cartridge may be damaged beyond easy repair and will need to be replaced. Also note, if you are using refilled (re serviced) cartridges, they have a shorter life span and can be hit and miss as the cartridge is being used beyond its intended life span.
If you let the cartridges sit too long (weeks / months) before printing again, the cartridges will dry up.
Chris

There are pads inside the printer that collect excess ink and hlep to keep the print heads clean , and they need to be changed.

If you are getting an error that says "wrong cartridge" then the ink cartridge you are trying to use is defective. Return the cartridge to the store you bought it at and get another one. Do not use refilled cartridges unless they are purchased by a professional who knows what they are doing. Your problem lies with your ink cartridge and not the printer.