20 Most Recent Canon PIXMA iP5000 InkJet Photo Printer - Page 7 Questions & Answers

code for reset canon ip1000 :

1. Press and HOLD down the POWER button, then release power button
2. so press again power button, u printer so ready for printing
3. enjoys.. have fun !

change toner

This printer is not designed for wireless. Use USB cable or direct print port.

Hi, i guess it is out of warranty, i suggest you change the power cord to see if the problem is not from the cord. If it does not still power up, i advice you get a technician to help you look into it, it is possible that one or two components on the board might be bad and needs replacement and servicing. So get a technician to help.

I wish you best of luck.

The Canon Pixma 5000 is an excellent photo printer!
Check that ALL your ink cartridges have ink and also run a cleaning cycle as your heads may be dirty and also do an alignment run: check your manual for instructions.

Under the circumstances go to control and click on printer. Clear all the printing jobs. Switch off the printer and the computer. Wait for sometime and restart the computer and the printer. This should clear your problem.

Then you close the tray so that it will continue printing. That is a warning that you should close the tray so that the printer will work properly.

I have to ask this question of you, just to make sure this is not an issue. Are you using a factory new ink cartridge?
Please consider the following:
If you are using a refilled or third party cartridge that may well be your problem. Most manufacturers build logic into their products to prevent the use of “Other Equipment Manufactured” cartridges as well as re-filled cartridges.
They do this to prevent problems from contaminated inks causing problems with print quality or damaging the physical printhead.
If you are using factory new cartridges, then please call the manufacturers Technical Support for assistance with the warranty on the cartridges
Don

You can view a tutorial from Canon support here: (copy and paste link into your browser)

http://www.usa.canon.com/consumer/controller?act=ModelInfoAct&fcategoryid=257&modelid=10439#SupportDetailAct

Type question: "How do I remove the print head"
Click "Search" button.
View the tutorial.

Print 4" x 6" photo images in normal mode in about 60 seconds; up to 17 ppm ... 3/4 Envelope. 9 Envelope. A4. A5. B5 Envelope. C5 Envelope. DL Envelope. 6 3/4 ...lexmark.com/lexmark/product/home/15/...?tabId=1

here you go :)

http://software.canon-europe.com/products/0010100.asp

This error mean "non installed or defective print head".First open cover and remove the ink cartridges.Then open holder and remove the print head.Clean the contacts on printer and print head using piece of cotton and some alcohol.Then put back all again.If the problem persist you need to replace the print head.It's part number is QY6-0057.

Your rollers are not up at that side, try manually raise them up to see if that helped.

When elements on the printhead burn out, that's what it looks like.You need a new printhead, QY6-0057-000, around $50.00

I assume by cleaning you mean pressure FLUSHING the ink channel with cleaner, not just wiping the head. You have to charge the ink channel after flushing to prime it.

The cost of a replacement part probably makes it un-economical to do a replacement.

Testing for electrical problem without schematics would be hard.

Do check that the flex carriage cable connection is good.

1. Connect device to another computer 2. Disconnect and reconnect the USB cable to ensure a secure connection 3. Confirm the printer is displaying properly in Device Manager (Windows 98/Me) 4. Confirm the printer is displaying properly in Device Manager (Windows XP/2000) 5. Disable third-party software 6. Press the POWER button to power on the printer 7. Restart the computer 8. Try a different data cable 9. Uninstall / reinstall the printer driver (Windows) PIXMA Printers

try to use another cartridge.

if it doesn't work, try to look at contacts between cartridge (it seems at head of cartridge) and inner part of your printer. Make sure it is not blocked.

It seems the nozzles of one of the ink chamber are clogged, try deeping the nozzles in warm water for 5-10 minutes to remove the clogg.

Welcome Tony

Looks like you got a bad plunger that could be so full of dried ink or just clogged. you could by a printer service kit and see if that shores it up if not the plunger would need to be replaced.. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edwy_1a56970cf1ea4620