20 Most Recent Yamaha Stator Super Jet 700 Sj700 1996-2012 Generator - Page 8 Questions & Answers

Use a standard battery charger set to a low setting like two amps for a few hours.

You can disconnect the fuel line from the carb and drain the gas. It would be even better to then remove the fuel tank. If this is the generator with the large plastic tank, quite often the rubber gromet in the bottom of the tank with shout off vavle in it will deteriorate into a black gooey mess, and leak. If so that will have to be replaced. Clean inside of tank with fresh gasoline. Remove bowl from carburator and clean throughly. If you know how to work on engines, remove the carburator and clean throughly, notice how all springs and linkage were connected before removeal. Be sure all passage ways in carb are clean. Always use sta-bill in your gas.

http://www.yamaha-motor.com/assets/service/manuals/0/LIT-19626-01-15_1425.pdf

Fuel Starvation - Float Bowl Carburetor
1) remove air filter assembly
*be cautious of tearing the mounting gasket. If it does tear, you HAVE to replace it. It is part of the priming system
2) remove the float bowl fastener. This is the main jet
3) carefully remove the float bowl, the rubber o-ring/gasket will not be able to be used if it is removed, you WILL have to replace it
4) using a spray 'carb cleaner'
spray up thru the center of the carburetor
spray and clean the main jet with cleaner and 'tag' wire
(tag wire is very thin, and can be used to clean the hole in the center of the main jet)
5) clean any debris from inside the bowl or carb body
6) re-install bowl and center bolt, air filter assembly

*if you need gaskets, your local lawn & garden dealer can supply. The kit is cheaper than individual gaskets, and all the parts needed to finish the above repair are in the kit. I’m happy to assist further over the phone at https://www.6ya.com/expert/rolandw_c013176d62ee17ae

Surging is not uncommon till warm and stable,

No power? Read this site:

http://www.endtimesreport.com/dead_gen.html

Check the Built in circut breaker.

I'm not quite sure if your issue may relate to most inverter and auto-load sensing generators or some gas-powered equipment.
Most power cutters/grinders such as Stihl or Husqvarna, specially the higher cc models do sound crappy without load, you'd think there's something wrong with it from day 1. This is normal. Well, some of these machines lack the load sensing capability thus does not adjust throttle variably according to load.
Modern generators, specially the inverter ones along the 1000 to 3000 watt range where the Yamaha 2400 falls into category, have a switch where you can choose to let the unit sense and adjust throttle according to load. If this is off, the unit might sound like its not running smoothly on idle. Depending on you, this can be alarming or not. On a Honda EU2000is, for example, it is noticeable when the auto-load sensing button is off but not be like its choking or sputtering.
Anyhow if it is idling roughly, I can only come up with 2 possible causes, if I may suggest:
1.) the cable that gradually pulls the throttle (to open wide or close) on the carburetor - normally called governor cable (although it has different configurations on different engine types) needs to be adjusted/tightened. Or replaced, if worn out. Before new cable, put lithium grease on cable - it helps a lot.
2.) throttle adjustment might be necessary. At most Yamaha servicing dealers, it is included when you have a carburetor tune-up. They will check the diaphragm for blockage or holes, gaskets for leaks and filters, well, the entire integrity of your carburetor. This resolves most rough idling issues.
I know it would probably save you at least $65.00 if you have to check this yourself and buy the spare parts. However, going to a servicing dealer may be the best solution but always be sure the repairs are warratied. Hope this helps.

You will need to know the BTU value of each type of fuel to compare the difference of each to one another. Nito methane is not a fuel as such, it does bring extra oxygen into the mix.

Check your air filter, and the oil level.
Make sure you're running on a flat surface.
You may also want to clean the carb and all the carb jets with spray carb cleaner, and check the gas filter screen at the tank exit.

Tom...what can I say - what you did was not very smart. Next time draw a diagram BEFORE you take the wires off!

My answer:

Hello Bill:

Here are the site links you'll need to check and/or get info, or buy your adapter kit for your Yami YG4600D Genset conversion kit.

Most likely it's running an 8 or 10HP engine on it now? In any case it's most likely less then 12HP. Not sure what size engine you have, as you didn't say only for the model #? On older Gensets it's harder to track down the HP rated engine is all.

For your Yami YG4600D Genset there you most likely will have your choice of at least 4 adapter kits depending on if you are going to keep gasoline as an option. If you're definitely NOT going to be ever running gasoline again then there are 1 or 2 adapter kits to choose from.

Use the site links below, and then browse whichever area you want as there are many options there. The last link listed takes you through all the different engines by make & model #'s.

I would also shop around locally where you are in LA, as you might be able to get that adapter kit for a lot less then the $227 to $267 they are asking for there at that site.

If you don't see your exact model # (or kit) there call them on their 800 toll free # listed at their site.

Also - if this site doesn't meet your expectations customer service wise at least you will have a starting off point with the wealth of information supplied there!

http://www.propane-generators.com/what_kit_do_i_need.htm

"What Kit Do I Need?"

http://www.propane-generators.com/simple_explanation.htm

"Simple Explanation"

http://www.propane-generators.com/a-c_kit_list.htm

A and C Kit List
Please post me a reply as to this info helping you solve your adapter kit problem there by following my posting recommendations above. Also please rate my troubleshooting fix as well.

Keep me posted and I'll follow up as well.

Best regards,

Frank

Yes

No one gives sizing. https://generatorguru.com/spark-plug-27901063/ https://www.google.com/search?q=united+power+generator+Model+GG2900+parts ..

https://cleanestor.com/how-to-clean-up-freon/?expand_article=1 This should help

No connecting to your utilty company in South Africa. Just FYI, we are a North American site and my not always have the answer, in this case we do Https://www.facebook.com/ConlogSolutions/posts/im-having-a-rf-con-error-cant-do-anything-on-the-gadget-please-help-on-how-to-re/962048393965724/ Quoting from link above: "Conlog Hi Ola-daniels, Please see below steps to assist with RFCON error : * Press the Back arrow on the keypad - this step is to refresh the UIU ( the device) * Type # 75 # - this is to check the signal strength If it does not go back to the normal display *Type # 80 # - this is to refresh the meter Then lastly you can repair the meter and the UIU by # 36 # The above steps will work better if you are outside the house because the meters uses the radio frequency connection The above error will occur in instances of bad weather conditions or if there is load shedding or power failure If the problem persists after trying the above you may contact the municipality or the service provider."

SOLVED: How do I clear up the rf con error on my meter ...

https://www.fixya.com > ... > The

May 7, 2020 - How do I clear up the rf con error on my meter because I want to ... Https://www.facebook.com/ConlogSolutions/posts/im-having-a-rf-con-error- ... Hi Ola-daniels, Please see below steps to assist with RFCON error : ... shut down the energy alimentation for 2 minute ,but if the defect persist error it show again. SOLVED: Pole meter conlog rf con meter keep on freezing ... Jan. 10, 2017 Meter reading shows rF CON instead of units available - Fixya Jun. 24, 2018 SOLVED: Good day my conlog ip54 elecricity meter showd ... Oct. 6, 2018 SOLVED: Rf con error - Fixya Jun. 20, 2020 More results from www.fixya.com

Please Help With My Conlog Prepaid Meter - Technology ...

https://www.nairaland.com > please-conlog-prepaid-meter

Aug. 6, 2020 - ystar: If the conlog meter is showing rf-Con, it means power supply doesn't reach the meter at all its either Loss of phase from the transformer or a loose contact ... How Do I Load The Activation Token On My Conlog Prepaid ... Mar. 17, 2020 I Need A Technician To Fix This... - Nairaland / General - Nigeria Jul. 22, 2019 I Need Number Codes To Reset Memmcol Prepaid Meter ... Jan. 11, 2019 More results from www.nairaland.com