Baumatic 23 in. BDW13 Built-in Dishwasher - Answered Questions & Fixed issues


heat sensor malfunction.
Located near the heater element on the under side will be a thermostat. Its ******* to the tub and its usually at the back. That's the temperature sensor you need to check. If you have a multi meter you can test for continuity through it and if its faulty then it will need to be replaced.

Baumatic 23 in.... | Answered on Apr 05, 2016 | 88 views


Here is a link to the error codes for your washer. http://www.manualslib.com/manual/213875/Baumatic-Bdw13.html?page=25
Also, another link to an incredible source of info on a whole host of manufacturers' diagnostic routines--your model is on page 19, includes how to enter diagnostic mode, etc. I hope this helps you!

Baumatic 23 in.... | Answered on Oct 04, 2015 | 230 views


This was answered on Fixya before. Just scroll down to the bottom of the post after you click the link:

http://www.fixya.com/support/t16086068-dishwasher_won_39_t_fill_e4_flashing

Baumatic 23 in.... | Answered on May 24, 2014 | 60 views


My beko oven and hob both are not reaching full temperature

Baumatic 23 in.... | Answered on Jan 05, 2014 | 76 views


Do one thing apply a good force of water in that what ever would be there it would be drain out with a force of water.
here

Baumatic 23 in.... | Answered on Nov 21, 2013 | 70 views


no I get copy of engineer in to checked the problem but not solve. they said to get how of the company maybe you guy would no the problem

Baumatic 23 in.... | Answered on Nov 04, 2013 | 131 views


The E3 code means - Longer heating time.Not reaching required temp. Cause - Malfunction of temp. sensor or heating element. Good luck !

Baumatic 23 in.... | Answered on Aug 28, 2013 | 1,433 views


It is possible that the machine does not start off the cycle because there are errors or feedback from the inputs. For the program to start up the main program controller must initiate the INLET/PUMP MOTOR/DRAIN to work when it is commanded .If this does not happen then the voltage at these points must be checked or the fault relates to no voltage/drive from the controller. This means the controller is a suspect.

Check how to remove the control panel: http://www.espares.co.uk/advice/dishwashers/a/3/1287/how-to-replace-a-hotpoint-dishwasher-fascia-p.html

If the water flows then the flow should be good, if not the inlet valve is bad or there is dirt in the filter. Also check the flow at the inlet of the water line. What is most important for the motor to start functioning is that the door switch must be ON when the door is shut or this will be an error for starting the motor. The water pressure must be good and the spraying must be seen to be good. If there is low pumping or pressure then the spray arms will not turn around to inject with pressure. If so the pump must be checked for clogging.

To replace check this link:

http://www.espares.co.uk/advice/dishwashers/a/3/1293/how-to-replace-the-spraying-system-on-a-dishw.html

Baumatic 23 in.... | Answered on Jan 11, 2013 | 37 views


You will have to check if the dishwasher pump is constantly running . If the only way you can stop is by turning off the power supply, the float switch has tripped. This means ther is either water collected at the base of the dishwasher due to a leak or the float switch is faulty. ther may be an error code on the panel if this is the case.

Baumatic 23 in.... | Answered on Jul 19, 2012 | 157 views


E3 error arises due to the malfunction of temp sensor or the heating element. Check for the thermostat.

Baumatic 23 in.... | Answered on Jul 02, 2012 | 1,746 views


Dear Sir:
You must fit very well the door catch. The switch is the elements most important for to run the dishwasher. Otherwise you must waste your time.

See the diagram attached, and you will the switch door must be close for to close the starting relay for RUN the main motor.

sincerely. God bless you
5_5_2012_4_48_32_pm.gif

Baumatic 23 in.... | Answered on May 05, 2012 | 99 views


Use a cap of white vinigar in the bottom of the washer before you use it.

Baumatic 23 in.... | Answered on May 02, 2012 | 67 views


Check that the arms spin freely when spun by hand, then check the outlet jets at the trailing end of the arms are not blocked with food particles and other solid matter. This often happens and the arm is unable to turn because the water jet that is supposed to drive the arm does not have the force to rotate it with the result is that the upper dishes do not get enough water and chemicals. .

Baumatic 23 in.... | Answered on Jan 30, 2012 | 259 views


Tap on the water inlet valve at the rear of the machine with a hammer handle and see if it may be stuck closed, this does happen on occasion.

Baumatic 23 in.... | Answered on Jan 24, 2012 | 292 views


too much power on one circuit will trip the breaker.

Baumatic 23 in.... | Answered on Jan 05, 2012 | 89 views


It will probably need a new spring.

Baumatic 23 in.... | Answered on Nov 17, 2011 | 68 views

Not finding what you are looking for?
Baumatic 23 in. BDW13 Built-in Dishwasher Logo

153 questions posted

Ask a Question

Usually answered in minutes!

Top Baumatic Dishwashers Experts

Pierre Laplante

Level 3 Expert

2042 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Peter

Level 2 Expert

199 Answers

Are you a Baumatic Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...