Top 20 Baumatic 23 in. BDW13 Built-in Dishwasher Questions & Answers

It may be sticking due to hard water deposits.

heat sensor malfunction. Located near the heater element on the under side will be a thermostat. Its ******* to the tub and its usually at the back. That's the temperature sensor you need to check. If you have a multi meter you can test for continuity through it and if its faulty then it will need to be replaced.

Here is a link to the error codes for your washer. http://www.manualslib.com/manual/213875/Baumatic-Bdw13.html?page=25 Also, another link to an incredible source of info on a whole host of manufacturers' diagnostic routines--your model is on page 19, includes how to enter diagnostic mode, etc. I hope this helps you!

Al you have is pos and neg
Sounds the black are neg

This was answered on Fixya before. Just scroll down to the bottom of the post after you click the link: http://www.fixya.com/support/t16086068-dishwasher_won_39_t_fill_e4_flashing

My beko oven and hob both are not reaching full temperature

Do one thing apply a good force of water in that what ever would be there it would be drain out with a force of water. here

no I get copy of engineer in to checked the problem but not solve. they said to get how of the company maybe you guy would no the problem

It is possible that the machine does not start off the cycle because there are errors or feedback from the inputs. For the program to start up the main program controller must initiate the INLET/PUMP MOTOR/DRAIN to work when it is commanded .If this does not happen then the voltage at these points must be checked or the fault relates to no voltage/drive from the controller. This means the controller is a suspect.

Check how to remove the control panel: http://www.espares.co.uk/advice/dishwashers/a/3/1287/how-to-replace-a-hotpoint-dishwasher-fascia-p.html

If the water flows then the flow should be good, if not the inlet valve is bad or there is dirt in the filter. Also check the flow at the inlet of the water line. What is most important for the motor to start functioning is that the door switch must be ON when the door is shut or this will be an error for starting the motor. The water pressure must be good and the spraying must be seen to be good. If there is low pumping or pressure then the spray arms will not turn around to inject with pressure. If so the pump must be checked for clogging.

To replace check this link:

http://www.espares.co.uk/advice/dishwashers/a/3/1293/how-to-replace-the-spraying-system-on-a-dishw.html

E3 error arises due to the malfunction of temp sensor or the heating element. Check for the thermostat.

You will have to check if the dishwasher pump is constantly running . If the only way you can stop is by turning off the power supply, the float switch has tripped. This means ther is either water collected at the base of the dishwasher due to a leak or the float switch is faulty. ther may be an error code on the panel if this is the case.

Dear Sir:You must fit very well the door catch. The switch is the elements most important for to run the dishwasher. Otherwise you must waste your time.See the diagram attached, and you will the switch door must be close for to close the starting relay for RUN the main motor. sincerely. God bless you

Use a cap of white vinigar in the bottom of the washer before you use it.

Tap on the water inlet valve at the rear of the machine with a hammer handle and see if it may be stuck closed, this does happen on occasion.

I'm not really sure what the solution is to this problem.

too much power on one circuit will trip the breaker.

Yes.

It will probably need a new spring.

Hello, cuddy I was trying to help you out here. I was going back to some customers that asked questions in the past and it appeared that no one answered them, so I thought I would take some of my personal time to see if I can help. Here is a link to about everything you want to know about your dishwasher, from repair to trouble shooting it,pictures, video's. Just scroll around and you will see tons of information to almost any question you might have on your dishwasher. If you go to this link and click around, I am sure you will find out so much about your dishwasher, you will know more that the company that made it. Here Is the link for you to click on>> http://home.howstuffworks.com/dishwasher.htm Please if this helped you at all, if you can find the time to rate my help and some kind words written would be appreciated for my free help , I would appreciate it. Here is also my direct link to my own pages of other areas of my expertise for other problems you might have in Automotive,Appliance, and Electronics. Drop In anytime for my help. Thanks,Mike http://beta.fixya.com/users/mc1bean

Hi

If the rotor is not spinning then the issue is with the motor or rotor that should be replaced. Hope this helps...please post back for further assistance.

Daniel