American Standard 9822.200.020 Bathtub Grab Bars 9822.200.020. Bathtub Accessories white. In satin 9822.200.295, polished chrome 9822.200.002. Whirlpool, Air Bath and Bathtub Grab Bar two per kit. Product Finish: White 9822.200.020. If you have any questions regarding - Page 6 - Answered Questions & Fixed issues
The pump will hum, but
If the pump hums and does not pump the water then there is a probability that the pump does not pump. Usually when most pumps spoil they still hum and sound like they are functioning fine but in actual fact they have stopped working. First get the pump checked out if it has water supply intact if the supply of water to the pump is okay then the pump might need replacement or fixing as this means the pump is bad.
Usually due to the cost of replacement pumps most people prefer to fix instead of just replacing, get a trusted expert to help you check if the pump is worth repairing or should just be replaced.
Hope this solution has been helpful?
Thank you for visiting FixYa.
7/14/2011 7:58:47 PM •
American...
•
Answered
on Jul 14, 2011
•
264 views
Whirlpool tub no longer turns
I would suggest that you have a electrician check the motor and make sure that the start capacitor is still good and that the switch is ok. It could be that due to lack of use that the motor needs cleaned and oiled. Thank you.
6/20/2011 4:02:48 PM •
American...
•
Answered
on Jun 20, 2011
•
112 views
Toilet flushes intermittently by itself.Water
Check the fill valve. it may have a bad seal inside or some trash in the water supply (iron or calcium deposits) may have clogged it. Do you hear water running when it's not flushing?
5/27/2011 1:02:24 PM •
American...
•
Answered
on May 27, 2011
•
163 views
Bought a aqua option toilet dual flush from
i have the same issue with my aqua option toilet. if you have a water shut off installed on the supply line to the toilet, just close it enough to reduce the supply pressure. no more splashing.
4/24/2011 1:29:50 PM •
American...
•
Answered
on Apr 24, 2011
•
928 views
I don't have the installation book, and I need to
What I would do is just overlay the existing floor with 3/4 inch 6 ply plywood'You would probably be ok without it but this will help to more evenly distribute the load.Thank you.
3/22/2011 1:04:44 PM •
American...
•
Answered
on Mar 22, 2011
•
226 views
My american standard jacuzzi tub
check the air tubing coming off the back of the motor. that tubing should connect from the air switch on the motor to the bottom of the air button on the top of your tub.
if it is not connected then it will never turn on.
2/20/2011 2:01:24 PM •
American...
•
Answered
on Feb 20, 2011
•
737 views
Jet tub pump is not working
It should be wired on a GFI receptacle or a breaker in your panel box. Check both of these before taking out your pump.
2/2/2011 6:49:28 PM •
American...
•
Answered
on Feb 02, 2011
•
85 views
My american standard low flush toilets are
Please contact our American Standard Customer Service Department -1-800-442-1902. One of our customer service representatives will be available to help you solve the problem
1/27/2011 4:57:39 PM •
American...
•
Answered
on Jan 27, 2011
•
223 views
The toilet takes a long
Is the flapper valve slow to return to the closed postion allowing water to flow through the flush valve? Make sure the toilet flapper is moving freely and is sealing properly against the flush valve. If there is no lengthy or continual water flow in to the toilet bowl then this is not the problem.
Is the water valve on the water fill line to the toilet tank fully open? This may seem silly but it could be this simple.
Check to make sure your fill valve is opening fully. If you have an older toilet there may be some deposits that need to be cleaned way to allow free movement.
If toilet does eventually fill to the desired level, there is no leakage, water valve on fill line is fully open and fill valve is opening fully then recommend you shut off water supply, drain toilet and disconnect water fill line from the water valuve and toilet tanke to make sure there is not a blockage. If the water line and connections are clear you may need to remove the fill pipe in the tank and check for blockage. If this is very old, conisdering the cost and effort, it may be simpler to replace at this time rather than trying to extend the life.
1/26/2011 4:54:28 AM •
American...
•
Answered
on Jan 26, 2011
•
639 views
Not finding what you are looking for?