Top 20 Baumatic MEGAWDSS Front Load Washer / Dryer Questions & Answers

well sort off.

likely is that the dampers on the underside of the drum have failed. (they are like shock absorbers)

The drum is also suspended from a couple of springs, you also need to check these.

To check springs the lid needs to be removed.

There normally are 2 dampers attached to the drum and the frame.

They are accessed by tipping the machine onto its side.

However the machine is heavy and make sure you disconnect power and water if you want to investigate.

Cost of new dampers are around 50 each.

---

Please dont forget to vote if you liked my answer

thanks

I had this problem, may be an easy fix if similar issue: Remove back cover. Take a look at the underneath the drum towards the right hand side. There may be a hook on a wire hanging there. If it is just hanging, there, it should be hooked onto a grey coloured lever, which has a hole on the edge of it. This is the drum brake which during the spin cycle releases the brake allowing the washer to spin. Hook the hook onto this grey lever through the hole. Replace the back cover. Test the machine with a towel or something, allow it to fill a little, then jump to the spin setting and see if it spins. Worth a shot, these are great machines.

I had this problem, may be an easy fix if similar issue: Remove back cover. Take a look at the underneath the drum towards the right hand side. There may be a hook on a wire hanging there. If it is just hanging, there, it should be hooked onto a grey coloured lever, which has a hole on the edge of it. This is the drum brake which during the spin cycle releases the brake allowing the washer to spin. Hook the hook onto this grey lever through the hole. Replace the back cover. Test the machine with a towel or something, allow it to fill a little, then jump to the spin setting and see if it spins. Worth a shot, these are great machines.

The front door seal is bad,check to see if there is anything jammed up inside that seal,money,ex,ex,lint

machine needs to be on half load for dryer to operate

go onto manualtree.com type baumatic megawdss washing machine, if this does not bring anything up scroll down until you see it in the listings. type in the code it asks for (this will be supplied underneath, its just to stop cumputers auto logging) and then download then manual. good luck

Hi there, check out this link for the manual. Cheers
http://www.manualnguide.com/manual-get/12345/

Yes probably. You didn't give a model # so this part may or may not work. But here it is..... https://www.ebay.com/itm/145011890040?hash=item21c361d778:g:mAkAAOSwJENkJeKD

https://www.glotechrepairs.co.uk/news/baumatic-dishwasher-fault-codes

Baumatic BWM50 manual, pg 50, indicates
e6 error is due to : Water level sensor failure short circuit or circuit break.

Sounds like a transmission issue. Is usually cheaper to replace an appliance than to do a major repair to one.

you probably turned it off before the empty cycle had finished

Drain the machine , drain hose next to drank plug , undo the drain plug and make sure there is nothing stopping the propeller turns using a torch to see with , if all turns and nothing lodged there then it's your pump ps easy job to do and cheap to repair your self , if you need more information get back to me colin evans

Check the Pump filter and pump

not saying this is whats wrong with it i just found this on the internet............hi, you need to empty the filter, ours does the same all too often. The filter is located bottom right of the machine at floor level, which is rather daft for an integrated applicance; we have to remove a whole length of plinth to empty ours. Be warned, a lot of gunge and water will come out so have towels at the ready, especially if you have a laminated floor. Turn the white slot with a a 10p piece......and empty. Not the most pleasant of jobs, but effective. Good luck!

It just pulls off, it takes quite allot of force.

something has gotten into the drain that has not got out causing it to rub against tub

Which model do you have? What happened that led up to the error? If you are sure there is no problem or problem has been fixed, try the reset button. Reset Buttons for Washing Machines

there is a dead short in the machine get in a service technician or an accredited electrician to check it out it may be at the wall plug or faulty cord to the machine