Powermatic 1610077K Model 60B 8-Inch 2-Horsepower Jointer, 208/230-Volt 1-Phase - Page 3 - Answered Questions & Fixed issues
R18CSP circular saw spares
no ------fixya doesnt sell products and doesnt have stores fixya is an online repair forum
6/7/2023 11:02:50 PM •
Saws
•
Answered
on Jun 07, 2023
•
32 views
Saw stops after 10 seconds?
All questions need FULL 'make model (what it is)', or they are impossible to answer.
Have you tried asking the maker? This sounds like a commercial quality automated saw.
4/6/2023 8:20:33 PM •
Saws
•
Answered
on Apr 06, 2023
•
63 views
My proxxon ks 230 table saw died when i pushed the wood i was cutting a bit harder against the blade. Is there a fix?
If your Proxxon KS 230 table saw stopped working after pushing the wood harder against the blade, it's possible that the saw's motor may have burned out or the blade may have been damaged or come loose. Here are a few troubleshooting steps you can try to diagnose and fix the issue:
- Check the power supply: Make sure that the saw is plugged in and that the outlet is functioning properly. If the saw is connected to an extension cord, try plugging it directly into a wall outlet.
- Inspect the blade: Check the saw blade for any signs of damage, such as chipped or missing teeth. Make sure that the blade is securely fastened to the arbor and that the arbor nut is tightened properly.
- Check the motor: If the blade and power supply appear to be functioning properly, the motor may be the issue. Check the motor for any signs of damage or burning, such as a burning smell or discoloration. If the motor appears to be damaged, it may need to be replaced.
- Contact the manufacturer: If you're unable to diagnose or fix the issue on your own, consider contacting the manufacturer or a professional repair service for assistance.
Please note that working with power tools can be dangerous, and it's important to take appropriate safety precautions when troubleshooting and repairing equipment. Always wear appropriate protective gear and follow all manufacturer instructions and guidelines.
3/18/2023 10:17:09 PM •
Saws
•
Answered
on Mar 18, 2023
•
58 views
CCW Wiring for LR63420 Model D Motor
Yes, it is possible to reverse the rotation of the LR63420 Model D motor from CW (clockwise) to CCW (counterclockwise). Here's how to do it:
- Turn off the power supply to the motor.
- Remove the motor cover to access the motor terminals.
- Identify the two wires connected to the start winding of the motor. These wires are usually marked with the letter "S".
- Swap the positions of these two wires. For example, if wire A is connected to terminal 1 and wire B is connected to terminal 2, then disconnect wire A from terminal 1 and connect it to terminal 2. Then disconnect wire B from terminal 2 and connect it to terminal 1.
- Reinstall the motor cover.
- Turn on the power supply and test the motor to see if it is now spinning in the desired CCW direction. If not, repeat steps 3-5, making sure to swap the correct wires.
Note: Reversing the rotation of a motor may affect its performance and should only be attempted if you are experienced with electrical wiring and motor repair.
2/28/2023 6:13:32 AM •
Saws
•
Answered
on Feb 28, 2023
•
112 views
Brushless 18vlt paddle switch grinder will start up then cuts out then repeats when tried again but slower and no power? What would the cause be? Thanks
There could be several potential causes for the issue you're describing with your brushless 18Vlt paddle switch grinder.
- Overheating: If the grinder is running for an extended period of time, it can overheat and shut off as a safety measure. If this is the case, the grinder will need to cool down before it can be used again.
- Battery Issue: The grinder may be shutting off because the battery is not providing enough power. This can be caused by a damaged or worn out battery, or by a problem with the battery's connection to the grinder. Make sure the battery is fully charged, check and clean terminals, test battery with other tools, if there is no improvement consider getting new battery
- Power switch issue: The switch could have a problem and it's malfunctioning, preventing the grinder from operating properly. The switch may need to be replaced in order to fix the issue.
- Motor issue: A problem with the brushless motor itself, could cause it to shut off under load or malfunction. The motor may need to be inspected and repaired or replaced.
- Power supply: If the grinder is running off of AC power, rather than a battery, the power supply may be faulty or not providing enough power to the tool.
I suggest you to start with trying to identify the problem by eliminating each possibility one by one. If you are not comfortable troubleshooting and fixing the tool, it may be best to reach out to the manufacturer or take it to a professional repair shop.
1/10/2023 5:14:30 PM •
Saws
•
Answered
on Jan 10, 2023
•
58 views
Not finding what you are looking for?