20 Most Recent Epson Stylus Photo R300 InkJet Printer - Page 8 Questions & Answers

HiThis is noting to do with the paper jam my friend. Click below and download the software and reset it and you are again ready to use your printer.Click here

1. open a document. 2. control-P - shortcut for print. then click properties, click maintenance, then click head cleaning. after this print check pattern. continue doing this until your light magenta and yellow ink gets clearer. if it didn't work replace your light magenta and yellow cartridge.

hi, this error is common on an epson printer which has already over flowing ink pads. 1st you must reset the counter. contact me so that i can walk you through on this process. my email si [email protected].

I think Your printer's software problem is occered. download ssc service utility and run irt on your pc. Then adjast wast ink absorver. After that you will relive from your printer problem.
Thank you

Hi

1. Make sure the printer is powered on, and not printing.
2. Open the printer cover.
3. Do one of the following:

3a. If the red error light is on (cartridge is empty) press the MAINTENANCE BUTTON.
3b. If the red error light is flashing (cartridge is low) press the MAINTENANCE BUTTON. You will now see the Cartridge Replacement highlighted in Advanced Settings. Select OK.
3c. If the error light is off (outdated cartridge), press the DOWN ARROW MENU button to choose MORE OPTIONS. Press OK, then select INK CARTRIDGE REPLACEMENT.

4. You will now see a message on the display telling you that the ink cartridge replacement will begin. Press OK to continue. The print head will move to the replacement position.
5. Open the cartridge cover. Press in the tab on the back of the cartridge, and lift the cartridge out of the printer. Dispose of it carefully.
6. Unwrap the new ink cartridge. DO NOT touch the green circuit boards, or remove ANY labels.
7. Lower the cartridge into the holder, with the green circuit board facing the front. Gently push the cartridge down until it is firmly seated.
8. If you need to replace another ink cartridge, repeat steps 5-7 above.
9. Close the cartridge cover. Press the front corner of the cartridge cover forward to lock the cover into place.
10. Press OK, and close the printer cover. The printer will begin charging the ink delivery system. Once charging is complete, press OK to finish.

First check the printer cable ia firmly attached to the printer and the computer.
If it still does not work then re-install the printer driver.
You can download the Epson printer drivers from theirsupport WEB site. Please click on this link and
select your model printer todownload :- http://www.epson.com/cgi-bin/Store/jsp/index.do?BV_UseBVCookie=yes

Form Epson's support page here:http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?oid=75683&infoType=Downloadsgood luck

You don't haveinstalled the driver. Use windows xp not windows 7.

Connect yourcamera directly to the frond usb of the printer and use your camera to print pictures.

Clean thecd tray especially the tree white marks and load the tray in the printer exactlyto the two marks >

Thewaste ink pad inside the printer is fully loaded with waste ink. You needto reset the waste ink pad chip. To do this you mast. 1. Press and hold "Stop", "Maintenance", and"Power" buttons for about 10 seconds. A message will comeon the screen saying counter is reset and to turn the printer off. TheR200 and others don't have a screen so just wait until the 10 seconds isup. 2. Turn the printer off, unplug the power cord. Wait about 1minute and power the printer back up. The counter will bereset. That's all there is to the reset procedure. 3. The waste padis actually full and ink is about to overflow, then you need to install a wastecontainer. You can see the waste pad by opening the access panel onthe back of the printer. Open theaccess panel on the rear of the printer (remove screw) You will see atube (down and to your left) coming from the cleaning pump and it willhave an open end on it. This is the tube that delivers ink to the wastepad. Use a piece of coat hanger wire or equivalent, and fish out this piece oftube. Bring it to the outside of the printer, thru the access panel. Findyourself a suitable container (Tupperware or a plastic cup or jar) that is nottoo tall. Put the tube into this container and secure the tube andcontainer so they won't come apart or lose connection if the printer is moved. Ifyou wish you can make a hole or notch in the access panel cover so it can bereplaced. Now the ink will go into this container and not into the waste padinside the printer. If it gets full, dump it.

Use head cleaning tree times in a row

Thewaste ink pad inside the printer is fully loaded with waste ink.You need to reset the waste ink pad chip. To dothis you mast 1. Press and hold "Stop", "Maintenance", and"Power" buttons for about 10 seconds. A message will comeon the screen saying counter is reset and to turn the printer off. TheR200 and others don't have a screen so just wait until the 10 seconds isup. 2. Turn the printer off, unplug the power cord. Wait about 1minute and power the printer back up. The counter will bereset. That's all there is to the reset procedure. 3. The waste padis actually full and ink is about to overflow, then you need to install a wastecontainer. Open the access panel on the rear of theprinter (remove screw) You will see a tube (down and to your left) coming from the cleaning pumpand it will have an open end on it. This is the tube that delivers ink tothe waste pad. Use a piece of coat hanger wire or equivalent, and fish out thispiece of tube. Bring it to the outside of the printer, thru the accesspanel. Find yourself a suitable container (Tupperware or a plastic cup or jar)that is not too tall. Put the tube into this container and secure thetube and container so they won't come apart or lose connection if the printeris moved. If you wish you can make a hole or notch in the access panel cover soit can be replaced. Now the ink will go into this container and not into thewaste pad inside the printer. If it gets full, dump it.

1. Press and hold "Stop", "Maintenance", and"Power" buttons for about 10 seconds. A message will comeon the screen saying counter is reset and to turn the printer off. TheR200 and others don't have a screen so just wait until the 10 seconds isup. 2. Turn the printer off, unplug the power cord. Wait about 1minute and power the printer back up. The counter will bereset. That's all there is to the reset procedure. 3. The waste padis actually full and ink is about to overflow, then you need to install a wastecontainer. You can see the waste pad by opening the access panel onthe back of the printer. Changing thewaste pad requires almost complete disassembly of the printer, it is a bigjob. There is an easier way. Open the access panel on the rear of theprinter (remove screw) and look inside carefully with a flashlight. You will see a tube (down and to your left) coming from the cleaning pumpand it will have an open end on it. This is the tube that delivers ink tothe waste pad. Use a piece of coat hanger wire or equivalent, and fish out thispiece of tube. Bring it to the outside of the printer, thru the accesspanel. Find yourself a suitable container (Tupperware or a plastic cup or jar)that is not too tall. Put the tube into this container and secure thetube and container so they won't come apart or lose connection if the printeris moved. If you wish you can make a hole or notch in the access panel cover soit can be replaced. Now the ink will go into this container and not into thewaste pad inside the printer. If it gets full, dump it.

Lire le message manuel ici

Read the manual post here.

May be the trouble is on the cartridge. Change the cartridge.. I find ask question similiar with your question. Just go to http://zoneprinter.com/error-tx111-tx111-did-not-detect-cartridge There are some trouble on that web, also the answer to solve that problem

Inkjet printers need to be used frequently to prevent inkdrying out in the print head nozzles.
If the print head cleaning maintenance routine does not clear the blockages,then print head needs replacing, but it may be expensive.
It may be more cost effective to buy a later model and better printer thanreplace the print head.