Top 20
Indesit 24 in. IDL500 Built-In Dishwasher Questions & Answers
IDL500- keeps tripping fuse when
Possible that there is a short within the power supply, the motor or the capacitor. You will need to check by disconnection of the circuits in isolating till trip over stops. Also if this is a ELCB then there can be leak in the circuit that trips due to the ground leak.
N01 light is flashing? Not working
"First green light flashing"... that meant the float cut off switch which is right at the bottom of the machine, was being activated by a water leak filling up the bottom tray where the float switch lives. The water inlet valve was closed to prevent any more flooding, and green light No 1 shows "no water entering machine".
In some cases, the leak was due to a burst in the short black rubber hose between the main pump and the water trap under the main filter and drain assembly. Need a new hose cured the whole sorry mess. To get at the relevant bits turn machine on its side and remove the bottom tray (six screws, three each side.
Good luck.
My Indesit IDL500 dishwasher cycles through (about
had this problem and apparently there's a 'float switch' in the bottom of the machine. This switch is a safety cut off and when activated can not just stop the machine but trip the electrics in the house. the reason for it activating is when food clogs up the drainage bit water can not drain and fills up the bottom of the machine. this then activates the 'float switch' as a kind of safety cut off.
the way to sort it is to disconnect the machine from the mains and drain and water. empty the clogged up food from the drain bit. then tip the machine back and a load of water will pour out (may need a load of towels for this bit or take the machine out the back and do it)
once this is done, plug it all back in and give it a try
I have an Indesit IDL500
Usually it is a relay on the control board that sends the signal to the heater. The control board will also sense the temperature from the thermostat (usually called thermistor) and turn heater off depending on setting. It could also be the thermistor is open circuit.
Best to first try the dishwasher on the fast cycle where heating of water is not invovled and confirm the dishwasher is operational. If this is ok then one can assume controller is reasonabley functional. The focus could then be the thermistor.
Detergent tablet does not dissolve
If you are putting the tablet into the dispenser and closing the lid the problem is that the lid is not opening as it should. No problem actually, just toss the tab into the floor of the dishwasher. it will work just as well. Joe
4 thumbs up. ty
The water decpenser will not
Hi,
I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works like new... However I have also found that if theheating element goes bad then that also can mess things up bad... So I wouldbuy new spray arms, and also check out the heating element to make sure it isworking... Here is a tip that will help you with the online buying...
Dishwasher
Spray Arms not Spinning
How to Buy
Appliance Parts OnlineA bad heating element causes many problems in dishwashers...
Dishwasher Problems The
Heating Element not WorkingDishwasher Maintenanceheatman101
Asker's Testimonial " explanation very clear. will give it a go and seehowsimple it was. thanks Ronnie " - ronnieshomes
Stays on heating cycle
Possible fault or error in the controller unit. it is important to check the sequence of the program and see the reson why the program never advances.
Perhaps some inputs must be checked for the reason the program stays stuck.
Can be the controller or relay of the heater.. check the thermostat.
Indesit di624
Firstly check the connection where the dishwasher hose connects to the drain. Remove this washe hose and see there is no stoppage at that piont. If all ok go to the dishwasher and see if there is no stoppage in the sump where the water goes out. If ok then the drain pump in the machine is either blocked or faulty. you will have to access this pump to be able to proceed further. good luck
My dishwasher is working fine . but the water is
Some have electrical heating elements that could be tested with a multi meter on the ohm scale. If the meter indicates that the element is open circuit it needs replacing and you should take note of the water seal and mounting of the element.
Ndesit IDL 535 DW, not cycling, water coming from under unt.
The washer is fitted with an anti flood device that detects water leaks and closes water inlet valve and puts washer in pump out mode. The anti flood device is a polystireen float with micro switch at the bottom floor of the washer. Dry the water and find the leak (pipe or pipe clamp) and this should then solve the error.
Not finding what you are looking for?