Top 20 Indesit 24 in. DE73 Evolution Free-standing Dishwasher Questions & Answers

Ciao Fabio.A12 significa che c'e' un problema con il circuito di riscaldamento dell'aqua. A12 appare quando il modulo di controllo rileva che il circuito che include l'elemento e'aperto.Elemento e circuito devono essere testati con il multimetro. Se l'elemento e' aperto deve essere sostituito. Se i cavi e l'elemento sono a posto, allora il problema e' il relay integrato nel modulo di controllo.Il caso piu comune consiste in un elemento diffettoso.In bocca al lupo.G.

from what i can find out, it means (auxillary wash pump triac cloesd/open circuit)

As you correctly pointed out A13 error is linked to the failure of the detergent dispenser lid operation.

If the lid is not opening at the correct time in the wash cycle, then the detergent will not be getting dispensed.

Either the controller circuit that operates the lid is faulty or the lid solenoid is faulty.

You can check the parts at this site.

Hi,
"Error A05 - Pressure switch has not been reset "

This is centered around the filter and drain area not working properly.
It is possible it just needs the filter cleaning and the hose flushing out, but also possible the pump needs to come out to clean it properly.
Drain it by putting the hose low down, and clean the filters of debris.
If this does not fix it, then remove the unit outside, lie on it's back and remove the pump to clean it.

no, you cannot connect the machine to a hot feed

A fault with the water heating has occurred. Book a service engineer

i looked on the indesit web site and got the manail for it. it means it has low salt

NEED TO REMOVE AND CHECK WIRING ESPE THE HEATING ELE AND MOTOR WIRES AND LOOK @THE HEATING ELE INSIDE THE ENCLOSURE CLOSE

Indesit Error Messages and Error Codes Indesit Dishwashers

• F10 - Fill or empty time out. Check that the hoses are not kinked, that the taps are on or whether the drain pump or hose is blocked.
• F11 - Heater timed out. The heater has not reached the required level. Book a service engineer.
• F20 - Temperature under range. Book a service engineer. .
• F21 - Temperature over range. Book a service engineer.

Fault codes for Indesit LCD Dishwasher Models

• A01 - Float switch operated - Book a service engineer.
• A02 - Open/Short circuit heater relay - Book a service engineer.
• A03 - Short circuit on thermistor - Book a service engineer.
• A04 - Unable to reach or sense temperature within 70 minutes - Book service engineer.
• A05 - Pressure switch has not been reset - Book a service engineer.
• A07 - Open/Short circuit wash motor triac - Book a service engineer.
• A08 - Open/Short circuit auxiliary wash motor triac - Book a service engineer.
• A09 - Open/Short circuit with main wash traic - Book a service engineer.
• A10 - Open/Short circuit fill valve traic - Book a service engineer.
• A11 - Half load valve traic or alternating motor action - Book a service engineer.
• A12 - Open circuit heater rely - Book a service engineer.
• A13 - Open/Short circuit dispenser traic - Book a service engineer.
• A14 - Drain hose too low causing syphoning. Check drain hose and re-adjust.
• H20 - Check tap and pressure of incoming water.

_uacct = "UA-1207243-4";urchinTracker();

ao5 is showing on the display of my indiset de73 dishwasher

A08 is a problem of the mother board , i changed this and i paid 130.000 for a **** ten minutes of work but i didn't resolve the problem. i waiting for another mother board.

Had a similar problem (flashing lights 1 and 2). Drained the machine by diconnecting the outlet hose and using a shallow bowl on the floor. Removed and cleaned filters. Forced clean water through by using a garden hose pipe(you can only do this one way, you cannot force water down the outlet pipe). Removed and cleaned the pump (you have to do this from under the machine but easy enough). Finally ensuring the waste trap under the sink was clear. Bingo!! No parts, no expensive engineer.

01 = Acquastop operated due to leak / overfill - machine drains until empty + lmin.

A02 = Heater Relay open circuit/short circuit or Thermistor or Safety T/Stat o/c or s/c or Element machine fills to Level Switch & Wash Pump runs.

A03 = Thermistor open circuit /short circuit - machine drains until Level Switch resets +1minute

A04 = Unable to sense/reach temperature in 70mins. - machine drains until Level Switch resets + lminute

A05 = Level Switch not resetting in within 3' 20" of drain commencing - machine drains until Level Switch resets +1 minute

A06 = Not used see also H20 at end

A07 = Wash pump Triac closed/open circuit - check that Drain Pump is not disconnected or Aquastop operated

A08 = Auxiliary Wash Pump Triac closedlopen circuit - check Wash Motor operation- machine drains until Level switch resets+30"

A09 = Main Wash Pump Triac closed/open circuit - cheek Wash Motor operation- machine drains until Level Switch resets+30"

A10 = Fill Solenoid valve Triac closedlopen circuit - check valve/operation - machine drains until Level Switch resets+30"

A11 = 1/2 load Solenoid Valve Triac or alternating Wash Motor action - check Solenoid Valve operation & alternating Motor action, replace Module if required - machine drains until Level Switch resets +30"

A12 = Relay with open circuit - check Heater, replace Module if required - machine drains until Level Switch resets+30"

A 13 = Dispenser Triac incorrect operation closed/open circuit - Wash Cycle completes but with Dispenser Lid notfunctioning correctly

H20 = Static 'Fill Time exceeding 6 minutes - cheek for blockages/low pressure

Have you checked there is no water in the base of the machine (there is probably a float with a microswitch there).

If there is any water at all in the base the float rises and triggers the microswitch turning on the drain pump. Does the drain pump run even with the door open?

You could try tilting the dishwasher 45 degrees and see if any water comes out

There should be a hose on the back that is placed in a drain "usually kitchen sink". If it will not drain after this unplug the appliance and check the bottom for a food clog and clean if needed.

1.Position the rotary switch to reset.
2.Press the RH button, with the clockface on it, once for every hour of delay required. The display will change to 1H, 2H etc.
3. reposition the rotary switch to the number of the required program.
4.Washer will start program after the selected number of hours.
NB. If you select too many hours, cotinue to press button as display will count up to a maximum of 24H before retuning to zero again.

Have you checked there is no water in the base of the machine?

There is likely a float in there which activates a microswitch turning on the drain pump.

You could try tilting the machine through 45 degrees and see if any water comes out.

It could take only a cupful of water inside the base of the machine to trigger the safety switch

Try turning off the breaker to it for a few min… and then turn it back on that might reset it.

A01 keeps coming up. Can you help

you may have a bad heating element..or temperature sensor the water temperture is not getting hot enough to let the dishwasher run. you my reset it and try running the water in the sink until it reaches hot ... then try stating the dishwasher...let me know if this helps