What ever programme I put my washing through, the machine fills with soapy water and starts the cycle. However it will not drain the soapy water out in order to rinse the clothes. Instead the dial clicks round continously. If I manually select Drain or Spin it will attempt these actions, fail and the dial will then continue to click round. I've drained the machine by removing the front of the pump on the botttom right hand corner. I did find 10p piece lodged in the waste pipe. The pump appears to be whole and the impellor spins when the machine is on Spin Cycle but the the machine still wont drain. Can anyone help me please?
I have a maytag washer that when it fills with water it wont drain out..the spin cycle just makes a noise and it wont do anything..any ideas what i can do to fix it thanks
Posted on Nov 24, 2008
hi there my indesit wil103 keeps stopping and displaying a rapidly flashing red led and green leds 2&4 flash slowly please help as it has taken my duvet hostage many thanks
you will need to unplug the machine at the mains, give it two minutes and the auto door lock will release your duvet, however start saving the pennies as your pcb is knackered and you'll be looking at about £200 to fix it
Posted on Oct 25, 2007
Hi
There was a power cut in my house and ever since I am unable to get my washer / dryer to work. When I switch on the machine I get a flashing red light which seems to indicate that there is a problem with the door lock. The delay button ( green light ) and 1200 - 600 spin button ( green light ) are flickering on and off also.
I took off the door and re-aligned the lock pin ( was off line ) The door is now closing fine as was having problems with this.
Can anybody advise what I can do to resolve this?
I am based in Dublin,Ireland
Thanks in advance
it needs resetting
http://www.washerhelp.co.uk/diy-repair-help_5.html#cl_q4
the sequence is here on this site
Posted on Jan 22, 2008
Indesit WIE 147 - taking water in and draining (nothing else happens) - display shows 'F-03'. Please advise any possible fault and solution... Thanks. Tom
Indesit washing machine error code 3 (F03)
On certain Indesit washing machines, if the on off light is flashing 3 times, with a slight pause, followed by flashing a further 3 times, or if it is didplaying F03 you have an error code that is explained as follows -
NTC fault - check Thermistor and module connections.
The NTC is the thermistor, which is a modern-day thermostat. It’s inserted into a tube in the heating element and is filled with heat sensitive crystals that change their electrical resistance according to their temperature. By knowing what electrical resistance the crystals have at given temperatures they can tell the water temperature.
With this fault the NTC is either faulty, or there’s a dodgy connection to or from it or there’s a connection problem where it connects to the main PCB.
It’s not something you can easily fault find yourself unfortunately, apart from if there was an obvious broken wire.
Posted on Nov 16, 2008
I NEED A COPY OF INDESIT WIA101 INSTRUCTIONS ON HOW TO USE.
Hi - You can download the manual from the link underlined in blue below:
WIA101
Please take a moment to rate this solution & let us know if the information given was useful to you - Good Luck!
Posted on Aug 09, 2008
I can not start WIDL 106 washing/dryer machine. As soon as I plug the machine, ON/OFF-DOOR, Function Buttons and Drying LEDS Flashes rapidly. Recently I changed the washing machine wash element. Since then I run couple of trouble less washing cycles. Then the problem starts.
I manage to run the programs several times, although the LED were flashing by plug/unplug the pover supply cable. Every time it was harder and longer to run the programs, until it stops responding completly.
I think it is related to the electronic of the machine, but I would like to get your expert opinion.
It is a defectiv controller pcb. I think the eeprom on the controller pcb lost its program (happens often on Indesit machines).
The only solution I know is to change the controller pcb, - not a cheap solution.
I have the same problem with WIDL 106.
Posted on Oct 15, 2009
error code f-08 on indesit wixe127 washer
Error code F08 means that the heaterrrelay cannot be activated.
Check the connections to the Pressure switch, the Module,and the Heater element.
If you can, test the element of the heater to make sure it is o/k.
Hope this helps.
Posted on Dec 02, 2009
indesit washing machine showing f05
F05 means pressure switch jammed on full.
Remove lower rear panel of washer.
Remove large black hose on bottom of drum.
Remove and clean filter inside hose.
Refit and test.
Please rate my solution.
Thankyou.
Posted on Feb 03, 2010
My Indesit washing machine was in the middle of a wash when there was a power cut. The power to the house was resolved but no nothing happens to the washing machine, it is dead. I have checked the fuse and plug, all OK and there is poser going to the machine (it has been checked with a tester).
PCB has suffered a catastrophic failure due to the power cut, it will need to be replaced. if you have a power cut in the future always turn off your appliances, as the voltage can exceed the appliance recommended voltage. only leave a light on as lights can take the over voltage unless they are led type, you can but power drop sockets that when power is off it turns of the socket off so no power goes thought to the appliance.
Posted on Feb 01, 2018
FAULT CODE F06
I had this error and engineer said the meaning of the codes on the web are wrong as they don't like to disclose their real code meanings for pure protectionism reasons. F06 on IWD7145 is a burnt out door interlock IDC error. He replaced the part number C00085194 (replacement door interlock) and microritardator part number 085194 and it works ok now.
Posted on Sep 26, 2012
1,189 questions posted
Usually answered in minutes!
100 Questions
91 Questions
15 Questions
3 Questions
