20 Most Recent Intel Motherboard - Page 7 Questions & Answers

http://support.asus.com/Download.aspx?SLanguage=en&m=CM5571

MSI 1996
SOUND CARD REALTEK HIGH DEVICE BUS

go here http://www.epson.com

cable has 20 or 24 pin group it will only go in one way

need a model number for Intel Motherboard

Go to this link and check out the spec sheet http://computer.top-marchands.com/2011/09/intel-d875pbz-desktop-motherboard-875p-chipset-socket-p-pga-478102-52/

The p/n (FRU 49P1599) is a Gigabyte motherboard, their p/n GA-G8IGMIU Rev 1.1 It seems to be a socket 478 type with FSB 400 or 533MHz, Intel 845G chipset, and DDR1 memory. In the downloads section of Gigabyte's website it is not present, probably because it so old it has been removed. In this section there is the opportunity to get the manual for a motherboard and the CPU support list, amongst other downloads. A similar m/b, the G8IG model supports ONLY older Williamette and Northwood type P4 CPUs, not the (slightly) newer Prescott ones. I suspect that your CPU is not working because it is a Prescott type (or it is just broken). To check what process your CPU was made by use the program Speccy, or take a magnifying glass and examine your processor (having carefully cleaned it up) for the S-code, RK or BK number, and look it up on Intel website (ARK) or in CPU-World. AND you should contact Gigabyte technical support (you have to go through the register rigmarole) to see they are able to answer questions you may have, get the manual and the CPU support list. 9.April.2014

you need a new display

INTEL Graphics Media Accelerator 3100

The Intel G31 Express Chipset Integrated GMA3100 enables enhanced 3D and high-definition video technologies for a better end-user experience. 3D enhancements enable greater flexibility and scalability and improved realism with support for Microsoft DirectX 9.0c Shader Model 2.0, OpenGL 1.5. Intel Graphics also support the highest levels of the Windows Vista* Aero experience Jetway Tech On The Move Motherboard MI5 G31SVM

We cannot assume that your motherboard is dead, try these: Unplug computer power cable from the socket outlet.


First, check to be sure the power supply is switched to 120 V.
If it is, then do a minimum system configuration test. Turn off the ON/OFF switch on the PS back panel, and disconnect the cord. You don't want to work on the motherboard (MB) with standby power applied.
Disconnect all components from the motherboard (including floppy, CD, hard drive). Leave the power connector attached to the hard drive, as the power supply has a minimum load requirement (never run a switching supply without a load, unless it is designed to do so -- and few are). Remove the power connector from the Motherboard, then reinsert it (potential for bad contact in control circuit).
Remove the RAM, reinsert one stick (going for a minimal configuration).
Remove all PCI boards and AGP. The motherboard should be able to turn on and beep an error code even without RAM and video.
Plug the PS back in, turn on the back panel switch, and use your screwdriver to short the power button pins (ATX type of supply).
Double check which pins are the power switch pins in the documentation, as front panel attachment point functions are usually not obvious, and are easily mis-wired since the connectors come off so easily during maintenance.
When you touch the pins, the CPU fan should instantly start turning, and shortly thereafter, the MB should beep an error code.
If not, check the mounting for the MB. Some cases use a U shaped rectangular snap in receptacle for MB mounting screws. These commonly become bent or twisted, and can short out nearby traces sometimes resulting in dead board symptoms.
If the fan didn't start turning when expected, you probably want to repeat this minimum configuration test with the motherboard out of the box.
Put it on an insulated surface (e.g. pink packing foam or cardboard), being careful about electrostatic discharge (ESD) (however, my bet is ESD damage that disables a motherboard is rare).
Although I haven't seen it, your motherboard may require the video card to be plugged in to turn on.
I doubt this, though, as there is enough housekeeping to do before checking for the video card that the fan should have time to start to spin.
If it still isn't working, try the other memory stick, or remove all memory.
Double check all connections before applying power!

i am not familiar with this error you could
click start control panel administrive tools computer management then select event viewer depending on what operating sytem you have this may vary extend the events there you will ((see errors in red)) you will no what exactly what the error was and at what time it occured you might be able to work your way through the probleml hope this helps you

sssssss

Take a look here please: http://www.helpdrivers.com/motherboards/Intel/Motherboard_DH_xx_Series/Motherboard_DH61WW/ If you cannot find what you are looking for, try to connct a USB-wifi device and install a free driver updater to scan (this one for instance http://www.driverupdate.net/downloads/SlimDrivers-setup.exe )

DETAILS.

https://aa7-downloads.phpnuke.org/en/c61069/driver-via-ac97-vinyl-audio-series-free-download-full-review#.UvOqp7ROpTE FIND THIS.