Crown G2216u Eonon 7" Hd Lcd Pip Tv 2 Din Car Gps Dvd Player - Answered Questions & Fixed issues

I would study the service manual and service notes to find out why the temperature sensors do not work. Probably a supply rail down I would think to affect both of them.

The Power Crown XTi 6000 is a power amplifier, and it sounds like it is activating its protection circuit and not generating a Pulse Width Modulation (PWM) signal. There could be a few different reasons for this behavior. Some possible causes include:

• Overheating: The amplifier could be overheating, causing the protection circuit to activate in order to prevent damage.
• Short circuit: There could be a short circuit in the amplifier, causing the protection circuit to activate.
• Input signal issue: The input signal to the amplifier could be causing the protection circuit to activate. This could be due to a problem with the source, such as a malfunctioning mixer or a disconnected cable.
• Output impedance or load mismatch: The amplifier may have a mismatch in output impedance or the load impedance which can cause the protection circuit to activate.
• Firmware or software issue : There could be a problem with the firmware or software that controls the amplifier, causing the protection circuit to activate.

Without more information, it's difficult to say for certain what the problem is. It's recommended to check the manual for troubleshooting steps and also check for any possible firmware updates. If problem persist it's recommended to take professional help.

Not most service manuals can be downloaded unless you use a model close to the original. Try service manuals.com

Google should have a manual for your 1000 amp thermal and also try on the companies official website too for a manual. Try searching on YouTube as well and YouTube should have videos about amp thermal on - Crown Audio Players & Recorders

http://www.fixya.com/tags/crown_amplifier_fault

Probable power transistor failure.

If you have eliminated any shorted speakers, cables etc, then the only other cause is a shorted device on the power output board. Probably a device on the heatsink.

Hello, Sylvia - I have no idea what entity you meant to receive your question. You posted in the Fixya.com website, which is intended for asking and answering questions on how to go about REPAIRING THINGS. Plus, your question landed in the Fixya category for Crown (brand) Audio Players & Recorders. Perhaps you meant to message Netflix, or your local public library, or a person from whom you borrowed the DVD, or someone to whom you sold the DVD, or . . . Best wishes.

Is the fan supposed to be on. On some units it runs all the time on others when the temp hits a certail level. Which is it for your baby?

It's best to assume there is a short circuit in the power amp board. The unit is going in to protect mode to stop it blowing fuses etc. Could be caused by bad speaker wiring or connections by the way.

Component over heating . Main input output ic defective.

Do you mean that you would like to change from a 3 wire cannon plug to a 1/4" female?

Replace/repair fan.

That is a subjective statement. You need to measure the SPL at the speaker and check against the specs and also measure the power from the amp to have the data to check and compare with. That will give you an objective answer. You could have lost part of your hearing, I do not know!

I would suggest you take it to your local Crown repair depot. It sounds like a fault in the internal protection circuits or the outputs are blown. Without a lot more information I cannot help.

Unfortunately, there may be a number of reasons. it would be much easier to diagnose if were taken to a n authorized repair center. Here is the link to Crown support- Service Centers

Check speaker to power bank protection circuit. The circuit is faulty indicating to the power amp that speakers are disconnected that shuts down the amp to protect the unit

Please, what is the problem, what is the question?

Power output amplifier circuit should be checked. If there is any delay relay fitted, its drive circuit too should check. Check all the components at the main power amp output section. Refer its schematic diagram for more details. If you wish to get some details; check the site linked here. Viewing it in "Mosaic" will make surf easy. Surf the site with patience. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/

Interchange speaker, and input cable